203 COOL CELL Manufactured of quality cellulose paper, oven-cured with acrylic polymer glue and fungicides. #H2-64E.................................................................................. H2Pad 6” x 12” x 48” Pro Tec Edge 15/45 Flute #H2-65E.................................................................................. H2Pad 6” x 12” x 60” Pro Tec Edge 15/45 Flute #H2-66E.................................................................................. H2Pad 6” x 12” x 72” Pro Tec Edge 15/45 Flute begins by selecting heavyweight Saturation Grade Kraft Paper designed for high water absorption rates. This specialty Kraft is also formulated for consistent resin pick-up; a crucial step to ensure proper resin impregnation during manufacturing. Production of H2PAD contains critical formulation of acrylic polymer glues, melamine additive for fire resistance, and fungicide additive. A special viscosity additive ensures even application on each sheet. A proprietary resin The first oven bakes the resin coating on the paper. The second oven cures each sheet individually after corrugating and before pressing to ensure consistent glue contact points. A third oven cures each media block for three hours before cutting and sanding. Triple Curing Process Throughout the manufacturing process, technicians constantly monitor the moisture content of the paper. Consistent moisture content is critical to proper adhesion of glues and the curing process. Constant Monitoring increases pad life by protecting against UV light and mechanical damage when cleaning. Helps to prevent the buildup of algae and minerals on the air entry side of the H2PAD. Special wetting additive promotes even water distribution by reducing the amount water collecting on the pad surface. 3/4” ProTec Edging Cool Cell Cleaners See Page 324 Stainless steel wire retainers used to hold cool cell pads in place. Pad retainers add additional rigidity to the center of pads to help maintain straightness over time. Retainer Clips should be used to stabilize pads that are more than five feet high and and when pads are stacked. PAD RETAINER CLIP #HS756....................................Cool Cell Retainer Clip In order to ensure maximum pad life for pads in excess of 5 feet in heigh is recommended to install pad retainers to maintain pad straightness. See documentation below form HSMANUAL-019 (Evap System Manual) Pad Retainer Installatio Pad retainers (HS756) Are recommend for any pads exceeding 5 feet in height. Pad retainers are sold individually (HS756) or in boxes of 20 (HS756-BX20 Pad retainers may be used on any height of pad. P d retainers add additional rigidity to the center of pads to help maintain straightness over time. To install pad retainers run 1”x4” lumber for length of system. Pad retainer should be installed to support pads at their midpoint. See Figure Below. In order to ensure maximum pad life for pads in excess of 5 feet in heigh is recommended to install pad retainers to maintain pad straightness. See documentation below form HSMANUAL-019 (Evap System Manual) Pad Ret iner Installatio Pad retainers (HS756) Are recommend for any pads exc edi g 5 feet in height. Pa r t i r are sold individually (HS756) or in boxes of 20 (HS756-BX20 r t i rs may be used on ny height of pad. P add additional rigidity to t e center of pads to help maintain straightness over time. To install pad r t iners run 1”x4” lumber for length of system. Pad retainer should be installed to support pads at heir midpoint. See Figure Below. I is recommended to install pad retainers to maintain pad straightness. See do e on below form HS v P f 2 (H i m d i a s T d s t r midp S w. to en i life for ds i c s i i i i ll i r to i i i i l l i ee i i h i a l i i i ll i d i i i i i l i i i l i i i i To install pad retainers run 1”x4” lumber for leng i should be installed o su i i i i l INSTALL AT MIDPOINT
RkJQdWJsaXNoZXIy MTA3MzU=