27 GROWERSELECT HSCD401-SUB.ASY Key Qty Item# Description 1 1 HSCD401-3 Plate, Guide Pulley 2 1 HSCD401-9 Shaft, Idle Pulley 3 1 HSCD401-5-1 Pulley, Idle-Asy 4 3 605842 Washer, Flat 1.19” OD x 0.64” ID x 0.0585 THK SS 5 2 605523 Nut, Zinc 5/8” Jam-Chain Disk 6 4 1EMG3 Bushing, Chain Disk Carriage 7 4 60881 Cross Recessed Pan Head Machine Screw - Type I 8-32 x 3/4” SS 8 2 HSCD401-11 Spring, Tension 9 4 60883 Nut, 8-32, Nyloc-Ss Chain Disk Corner Assembly Key Qty Item# Description 1 1 HSCD505-6 Bottom, Corner, Chain Disk 2 1 HSCD505-19 Top, Corner, Chain Disk 3 1 HSCD505-20 End, Clear, Corner, Chain Disk 4 2 HSCD505-11 Clamp, Tube-Chain Disk Corner 5 2 HSCD505-8 Gasket, Bottom-Left 6 12 HS724 Nut, 3/8-16 Hex Serrated Flange 7 2 HSCD505-9 Gasket, Bottom-Right 8 3 HSCD505-18 Retainer Clip 9 1 HSCD505-17 Rod, L-Shaped-Chain Disk Corner Hinge 10 2 605832 Washer, 1/2”, Neoprene Bonded Seal 18-8 SS 11 10 605161 Bolt, Hex Cap, 3/8”-16 x 1 1/4” SS 12 2 6068015 Nut, Acorn-1/2”-13 SS 13 39” HSCD505-24 Gasket, Chain Disk Corner 14 15” HSCD505-25 Gasket, Access Door 15 1 HSCD505-30 Wheel, Chain Disk Corner 16 1 HSCD505-1 Shaft, Chain Disk Corner 17 2 HSCD505-23 Bearing, Chain Disk Corner 18 1 60686 Hex Bolt - 1/4-20 X 1 SS 19 1 0129150 Nut, Hex, Serrated 1/4”-20 SS 20 2 607092 Bolt, J, 3/8”-16 X 3-1/2” SS 21 2 60606 Nut, Hex, Finish 3/8”-16 SS 22 1 HSLABEL-251 Label, Warning, Chain Disk Corner 23 1 HSLABEL-252 Label, Warning, Chain Disk Corner-Spanish PARTS LIST DESCRIPTION PART NUMBER QTY ITEM PLATE, GUIDE PULLEY HSCD401-3 1 1 SHAFT, IDLE PULLEY HSCD401-9 1 2 PULLEY, IDLE-ASY HSCD401-5 1 3 WASHER, FLAT 1.19" OD X 0.64" ID X 0.0585 THK SS 605842 3 4 NUT, ZINC 5/8" JAM-CHAIN DISK 605523 2 5 BUSHING, CHAIN DISK CARRIAGE 1EMG3 4 6 Cross Recessed Pan Head Machine Screw - Type I 8-32 x 3/4" SS 60881 4 7 SPRING, TENSION HSCD401-11 2 8 NUT, 8-32, NYLOC-SS 60883 4 9 1 1 2 2 3 3 4 4 A A B B C C D D .X = .125 .XX = .032 .XXX = .005 ANGLES = 2 HOG SLAT Incorporated - DATE(S) SHOWN HEREON THIS COPYRIGHT DRAWING AND THE CONFIDENTIAL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF HOG SLAT Inc. AND SHALL NOT BE UsED OR REPRODUCED IN ANY MATERIAL FORM NOR BE DISCLOSED TO THIRD PARTIES WITHOUT THE PRIOR WRITTEN CONSENT OF HOG SLAT Inc. c SHEET2 OF5 B2 REVISION T.FULCHER DESIGNED DRAWN T.FULCHER CHECKED F.HARRIS F.HARRIS APPROVED DATE 5/4/2015 MATERIAL SEE NOTES SCALE N.T.S. DWG. HSCD401-SUB.ASY INTERNAL MANUF NUMBER TITLE CHAIN DISK ASY TOLERANCES UNLESS OTHERWISE SPECIFIED: LAS TOLERANCIAS A MENOS QUE SE INDIQUE LO CONTRARIO: [X] = 3 [.X] = .8 [.XX]= .13 3 4 5 4 2 1 5 6 6 7 9 8 PARTS LIST DESCRIPTION PART NUMBER QTY ITEM Bottom, Corner, Chain Disk HSCD505-6 1 1 Top, Corner, Chain Disk HSCD505-19 1 2 End, Clear, Corner, Chain Disk HSCD505-20 1 3 CLAMP, TUBE-CHAIN DISK CORNER HSCD505-11 2 4 GASKET, BOTTOM-LEFT HSCD505-8 2 5 NUT, 3/8-16 HEX SERRATED FLANGE HS724 12 6 GASKET, BOTTOM-RIGHT HSCD505-9 2 7 RETAINER CLIP HSCD505-18 3 8 ROD, L-SHAPED-CHAIN DISK CORNER HINGE HSCD505-17 1 9 Washer, 1/2", Neoprene Bonded Seal 18-8 SS 605832 2 10 Bolt, Hex Cap, 3/8"-16 X 1 1/4" SS 605161 10 11 Nut, Acorn-1/2"-13 SS 6068015 2 12 GASKET, CHAIN DISK CORNER HSCD505-24 39" 13 GASKET , ACCESS DOOR HSCD505-25 15" 14 WHEEL, CHAIN DISK CORNER HSCD505-30 1 15 SHAFT, CHAIN DISK CORNER HSCD505-1 1 16 BEARING, CHAIN DISK CORNER HSCD505-23 2 17 Hex Bolt - 1/4-20 X 1 SS 60686 1 18 Nut, Hex, Serrated 1/4"-20 SS 0129150 1 19 Bolt, J, 3/8"-16 X 3-1/2" SS 607092 2 20 Nut, Hex, Finish 3/8"-16 SS 60606 2 21 Kit, Hardware-HSCD505 HSCD505-28 1 N/S LABEL, WARNING, CHAIN DISK CORNER HSLABEL-251 1 22 LABEL, WARNING, CHAIN DISK CORNER-SPANISH HSLABEL-252 1 23 1 1 2 2 3 3 4 4 A A B B TITLE DESIGNED DRAWN CHECKED APPROVED DATE c HOG SLAT Incorporated - DATE(S) SHOWN HEREON THIS COPYRIGHT DRAWING AND THE CONFIDENTIAL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF HOG SLAT Inc. AND SHALL NOT BE USED OR REPRODUCED IN ANY MATERIAL FORM NOR BE DISCLOSED TO THIRD PARTIES WITHOUT THE PRIOR WRITTEN CONSENT OF HOG SLAT Inc. T.FULCHER T.FULCHER F.HARRIS F.HARRIS 10/25/2017 CHAIN DISK CORNER ASSEMBLY INTERNAL MANUF NUMBER SHEET OF 1 1 DWG. HSCD505 TOLERANCES UNLESS OTHERWISE SPECIFIED: .X = .125 .XX = .032 .XXX = .005 ANGLES = 2 A9 REVISION [X] = 3 [.X] = .8 [.XX]= .13 LAS TOLERANCIAS A MENOS QUE SE INDIQUE LO CONTRARIO: MATERIAL SEE NOTES SCALE N.T.S. 10 2 8 9 4 7 5 1 3 4 10 6 11 12 12 CROSS SECTION OF HSCD505-24 GASKET CROSS SECTION OF HSCD505-25 GASKET REVISION HISTORY REV DESCRIPTION DATE APPROVED A1 ADDED GASKETS TO BOM 5/21/2018 T. HAWKINS A2 FIXED RETAINER CLIP ITEMS IN BOM AND ADDED GASKETS 6/12/2018 T. HAWKINS A3 CHANGED PART NUMBER FOR WASHERS 6/14/2018 T. HAWKINS A4 CHANGED WHEEL TO INDIVIDUAL PARTS AND HSH099 TO 605832 6/18/2018 T. HAWKINS A5 CHANGE HSCD505-25 PROFILE 6/19/2018 T. HAWKINS A6 CHANGED RADIUS ON HSCD505-11 8/22/2018 T. HAWKINS A7 ADDED HARWARE KIT TO BOM AND ADDED OTHER PARTS TO ASSEMBLY 10/4/2018 T. HAWKINS A8 ADDED HSLABEL-251 AND HSLABEL-252 10/1/2019 T. HAWKINS A9 SWAPPED OUT HSCD505-4 FOR THE HSCD505-30 12/5/2019 T. HAWKINS 5 7 17 16 15 17 13 14 18 19 20 21 23 22 HSCD401 MOTOR-GEARBOX SUB Key Qty Item# Description 1 1 HSCD401-7 Weldment, Housing 2 1 HSCD-303 Plate, Mount 3 4 73834 Screw, 1/2”-13 X 1” Socket Button Cap SS 4 4 60616 Washer, Lock - Ss 1/2” 5 4 606061 Nut, Hex, 1/2-13 - SS 6 1 HSCD-301 Gearbox Transtecno 39.26:1 Nema 56C-140TC 7 8 61914 Bolt, M8 X 1.25 x 14mm SS 8 1 HS9032C Motor 1.5 Hp 1ph 60 Hz 208-230v 9 1 HSCD-311 Shaft, Output 10 1 HSCD313 Wheel, Drive, Cast-Assembly 11 2 HSCD-308 Washer, Op Shaft To Drive-Cd 12 3 61913 Bolt, M8 x 1.25 x 20mm SS 13 1 HSCD-306 Guard, Gearbox 14 1 HSLABEL-213 Label, Warning, Moving Parts-Eng./Spanish 15 1 HSCD-507 Key, 8mm x 10mm x 1.7in 16 2 HSCD-501 Key, 8mm x 10mm x 2.5in 17 1 HSCD-311-01 Spacer, HSCD-311 Rev A3 Shaft 18 2 60589 Washer, Lock 5/16 SS PARTS LIST DESCRIPTION PART NUMBER QTY ITEM WELDMENT, HOUSING-CHAIN DISK HSCD401-7 1 1 Plate, Mount, Chain Disk HSCD-303 1 2 Screw, 1/2"-13 X 1" Socket Button Cap SS 23268 4 3 WASHER, LOCK - SS 1/2" 60616 4 4 NUT, HEX, 1/2-13 - SS 606061 4 5 Gearbox Chain Disk Transtecno 39.26:1 NEMA 56C-140TC HSCD-301 1 6 Bolt, M8 X 1.25 X 14mm SS 61914 8 7 Motor 1.5 HP 1PH 60 Hz 208-230V Chain Disk Grower Select HS9032 1 8 SHAFT, OUTPUT - CHAIN DISK DRIVE - GS HSCD-311 1 9 Wheel, Drive, Cast-Assembly HSCD313 1 10 WASHER, OP SHAFT TO DRIVE-CD HSCD-308 2 11 Bolt, M8 X 1.25 X 20mm SS 61913 3 12 Guard, Chain Disk-Gearbox HSCD-306 1 13 LABEL, WARNING, MOVING PARTS-ENG./SPANISH HSLABEL-213 1 14 Key, 8mm X 10mm X 1.7in HSCD-507 1 15 Key, 8mm X 10mm X 2.5in HSCD-501 2 16 SPACER,HSCD-311 REV A3 SHAFT HSCD-311-01 1 17 Washer, Lock 5/16 SS 60589 2 18 1 1 2 2 3 3 4 4 A A B B C C D D .X = .125 .XX = .032 .XXX = .005 ANGLES = 2 HOG SLAT Incorporated - DATE(S) SHOWN HEREON THIS COPYRIGHT DRAWING AND THE CONFIDENTIAL INFORMATION CONTAINED THEREIN ARE THE PROPERTY OF HOG SLAT Inc. AND SHALL NOT BE UsED OR REPRODUCED IN ANY MATERIAL FORM NOR BE DISCLOSED TO THIRD PARTIES WITHOUT THE PRIOR WRITTEN CONSENT OF HOG SLAT Inc. c SHEET5 OF5 B2 REVISION T.FULCHER DESIGNED DRAWN T.FULCHER CHECKED F.HARRIS F.HARRIS APPROVED DATE 5/4/2015 MATERIAL SEE NOTES SCALE N.T.S. DWG. HSCD401 MOTOR-GEARBOX SUB ASY INTERNAL MANUF NUMBER TITLE CHAIN DISK ASY TOLERANCES UNLESS OTHERWISE SPECIFIED: LAS TOLERANCIAS A MENOS QUE SE INDIQUE LO CONTRARIO: [X] = 3 [.X] = .8 [.XX]= .13 8 6 5 9 2 7 7 11 10 1 3 4 11 12 13 14 12 15 16 17 18 18 WARNING: This product can expose you to chemicals, including nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov WARNING: This product can expose you to chemicals, including nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov WARNING: This product can expose you to chemicals, including nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
RkJQdWJsaXNoZXIy MTA3MzU=