Hog Slat Inc. Newton Grove, NC USA June 2023 Air Storm Fans AS-36EBDBPG Fan 36"FBG Panel 1.0 HP 1725RPM 115/230V 60Hz only AS-36EBDBPG-HV Fan 36"FBG Panel High Volume 1.5 HP 1725RPM 230V 60Hz only
Hog Slat Inc. Newton Grove, NC USA June 2023 2 Air Storm Fans Table of Contents GrowerSELECT General Page .................................................................................................................................3 Safety .........................................................................................................................................................................4 Warning Labels .......................................................................................................................................................4 Installation ...............................................................................................................................................................5 Operation Safety .....................................................................................................................................................5 Maintenance Safety ................................................................................................................................................5 Installation .................................................................................................................................................................6 Framing ...................................................................................................................................................................6 Assembly.................................................................................................................................................................7 Wiring...................................................................................................................................................................... 18 Pre-Operation Assessment .................................................................................................................................. 19 Operation ................................................................................................................................................................ 19 Maintenance ........................................................................................................................................................... 20 Troubleshooting .................................................................................................................................................... 22 Performance ........................................................................................................................................................... 23 Exploded Diagrams/Replacement Parts ............................................................................................................. 24 Hog Slat Limited Warranty.................................................................................................................................... 27
Hog Slat Inc. Newton Grove, NC USA June 2023 3 Air Storm Fans GrowerSELECT General Page General Installation Notes: Make sure that power is disconnected from system prior to servicing. Installation of this equipment and related OEM equipment should be in accordance with these instructions, OEM’s installation instructions and local codes (if applicable). Failure to follow specified instructions may cause damage to equipment and/or personal injury or death. Take special note of any Warnings or Safety Decals on the equipment and in manuals. Always wear protective clothing and any applicable Personal Protective Equipment (Safety Glasses and/or Ear Plugs) when working with the equipment. Discarded materials, equipment and boxes should be recycled in accordance with local and national codes. Safety Instructions: Read all safety messages in this manual and on equipment safety decals. Follow recommended precautions and safe operating practices. Ground all electrical equipment for safety. Ground all non-current carrying metal parts to guard against electrical shock. Always keep safety decals in good condition and replace missing or damaged decals.
Hog Slat Inc. Newton Grove, NC USA June 2023 4 Air Storm Fans Safety Warning Labels Warning Decals have been placed on the equipment to warn of potentially dangerous situations. Care should be taken to keep this information intact and easy to read at all times. Replace missing or damaged safety signs. Safety–Alert Symbol This is a safety–alert symbol. When you see this symbol on your equipment, be alert to the potential for personal injury. GrowerSelect equipment is designed to be installed and operated as safely as possible...however, hazards do exist. Safety decals should be read and understood thoroughly by individuals within the local area of the fan. Safety decals should be visible from both the front and back of the fan. Should a decal be missing or damaged, please contact Hog Slat Inc. for a free replacement: Hog Slat Inc. 206 Fayetteville St. Newton Grove, NC 28366 Toll Free: 800-949-4647 Local: 910-594-0219 The below safety decal should be represented and visible on both the front and back sides of the fan. This label is identified by the HSLABEL-080 part number in the lower right corner. WARNING – FLYING OBJECTS AND ROTATING PARTS Ensure fan guards are in place during operation. Securely tighten propeller to shaft to avoid slipping. Disconnect power supply for inspection or service when guards are removed and personnel are exposed to propeller. WARNING – HIGH VOLTAGE Disconnect electrical power before inspecting or servicing equipment unless maintenance instructions specifically states otherwise. Ground all electrical equipment for safety. All electrical wiring must be done by a qualified electrician in accordance with local and national electrical codes. Ground all non-current carrying metal parts to guard against electrical shock. With the exception of motor overload protection, electrical disconnects and over current protection are not supplied with the equipment.
Hog Slat Inc. Newton Grove, NC USA June 2023 5 Air Storm Fans Installation Prior to any installation product should be inspected for any damage caused during shipping. Any damage found should be documented and communicated to liable parties. Operation Safety When fan is in operation no attempt should be made to service or interact with parts from the fan. Any attempt to interact with fan parts while the fan is operating could result in injury. Inlet and exit guards and or shutters are in place to help prevent foreign objects from entering inside the outer perimeter of the housing. If maintenance to the fan is required, interrupt the source of power to the motor and allow propeller to come to a complete stop before moving forward with any efforts to service. Maintenance Safety Air Storm Fans are designed and built with operator safety in mind. Some safeguards must be disassembled or removed for the parts to be serviced or replaced. As this fan does have moving parts and is supplied with electrical power, steps must be taken to ensure safety around these presented hazards. READ THESE INSTRUCTIONS BEFORE SERVICE OR PART REPLACEMENT 1. Read and understand the operating manual before trying to install or operate Air Storm Fans. 2. Power supply should be turned OFF and LOCKED OUT for service to motor and electrical components. Use CAUTION in checking voltage or other procedures requiring power to be ON. 3. DO NOT attempt to bypass any safety features or devices to operate the fan. 4. Keep fan clean of all debris that may collect on the motor, prop, and any bearings, belts, or pulleys. 5. Use CAUTION in working around all moving parts of the fan. Fan guards or shutters must be in place before fan can be safely started and operational.
Hog Slat Inc. Newton Grove, NC USA June 2023 6 Air Storm Fans Installation Framing The rough in opening for the fan is an exact measurement that accounts for the heads of fasteners and openings for fan. Ensure there is proper clearance for installation or rough opening may require larger measurements. Fan Model Rough Opening (Width x Height) 36” Poly Outside Mount Panel Fan 43” x 43” (144.8 cm x 144.8 cm) Additional Mounting Holes may added to accommodate rough openings that range between large and small rough openings
Hog Slat Inc. Newton Grove, NC USA June 2023 7 Air Storm Fans Assembly 1. Remove packaging from fan and cone if applicable. • Locate hardware kit(s) and supplied literature and store for later use. • Ensure not to damage the fan or components during this step. Cut a Treated Lumber 2”x4” to 46” Length. Attach to the exterior of the building with the top of the 2’x4” 23 Inches above the center of the rough opening, and centered below the rough opening horizontally. Provided treated lumber is used the 2”x4” may be left in place after operation, alternatively after all lag bolts are installed the 2”x4” may be removed.
Hog Slat Inc. Newton Grove, NC USA June 2023 8 Air Storm Fans 2. This step require (2) installers. Place bottom of fan assembly onto the top of the 2”x4”, rotate until fan interior face of fan mates with the wall then secure using sheet metal screws (805060) the outer hole pattern is for the large rough opening, inner hole pattern for small rough opening. 3. Loosen set screws on both pillow block bearings. There are a total of 4 set screw, be sure to loosen only, do not remove! This allows the shaft to slide into position in following steps. 4. Rotate shaft plate into position and secure with carriage bolts, nuts, and washers from hardware bag number 4 as shown below.
Hog Slat Inc. Newton Grove, NC USA June 2023 9 Air Storm Fans 5. Install prop onto shaft allowing approximately 1 inch of the shaft to protrude through the hub of the prop. Correct orientation of the prop should have the set bolt facing the intake (motor) side of the fan. Use Key from hardware bag number 5 on prop end of shaft. Apply Loctite 290 to prop set bolt and secure to 150 inch lbs. Optional bearing shims are provided in hardware bag as well.. If needed these can be installed under the bearings to raise the height of the shaft. By design these are not needed but are provided in the rare case the height of the shaft needs to be adjusted. To install bearings shims simply loosen bearing hardware and slide bearing shims under the bearings and re tighten bearing hardware. Additionally if prop is off center horizontally bearing hardware should be loosened, prop centered, then hardware re tightened. 6. Rotate motor plate to align holes and install carriage bolts, nuts, and washers from hardware bag number 4.
Hog Slat Inc. Newton Grove, NC USA June 2023 10 Air Storm Fans 7. Loosen bolt holing tension arm in place and rotate as shown below. Once in place retighten bolt 8. Install motor onto motor plate as shown using hardware from hardware bag number 8. The motor should be centered horizontally and should be slide as far toward the exhaust side of the fan as possible.
Hog Slat Inc. Newton Grove, NC USA June 2023 11 Air Storm Fans 9. Install motor pulley onto motor shaft. Key to be utilized is taped to the motor. Do not tighten set screws at this time. Set screws should face the intake side of the fan. Motor pulley should be oriented with large side facing interior of building or intake of fan. 10. Install Belt by placing belt around tension arm and drive sheave, then rotate large pulley so the belt rotates onto the assembly. Check for proper tension, the second indicator mark on the belt tensioner is the desired operating tension. If belt lacks tension adjust tension arm as needed ! ENSURE ALL PULLEYS AND DRIVE COMPONENTS ARE PROPERLY ALIGNED TO ALLOW THE BELTS TO OPERATE ON THE SAME PLANE ! If required, loosen bearing set screws to adjust drive pulley location. If loosening bearing set screws alone don’t not allow shaft to move loosen the mounting hardware of ONE of the bearings to free shaft 11. Once components are aligned validate clearance of prop around orifice and also check for clearance between the prop and motor. There should be a minimum of ¾” clearance between the prop and nonshaft end of motor. Finally tighten all set screws on bearings, on pulleys and recheck set bolt on prop. Validate all hardware is tight before continuing.
Hog Slat Inc. Newton Grove, NC USA June 2023 12 Air Storm Fans (Optional) Attach weather stripping to the outside of the orifice roughly ¼ inch form the minor edge (shown in red) Remove Butterfly assembly crate. Insert 4 cap head screws from the inside of the butterfly assembly (holes are threaded to hold fasteners in place). Tighten with Allen wrench until snug.
Hog Slat Inc. Newton Grove, NC USA June 2023 13 Air Storm Fans 12. This step requires (2) installers. Hook the butterfly assembly on the top of the outside of the orifice. Ensure the vertical support is properly aligned and the butterfly is oriented correctly (SEE BELOW IN RED) before continuing. Manipulate the orifice inside the butterfly assembly and loosely attach the mounting brackets with lock nuts. Press butterfly onto the fan assembly until the edge of the throat bottoms out against the vertical and horizontal members of the butterfly assembly. At this time also inspect tightness of fit of the butterfly to the orifice. BE SURE TO VALIDATE BUTTERLFY ORIENTATION AGAIN! SPRING ATTACHMENT BOLTS SHOULD BE ORIENTED TOWARDS THE GROUND. 13. From inside the house attach the butterfly spring bracket as shown. Then attach both supplied springs onto the predrilled holes in the bracket securing the other end to the bolts on the butterfly door using supplied 1/4”-20 stainless lock nuts from the hardware kit
Hog Slat Inc. Newton Grove, NC USA June 2023 14 Air Storm Fans 14. Assemble cone. This step requires (2) installers. Begin by placing one cone panel on the ground with the end with connection slots slightly elevated. Insert the connection tabs into the connection slots and rotate to parallel. Continue for all 4 panels. Connect cone panels to form round shape. This step requires (2) installers. Stand the cone upright with the larger diameter on the ground and force the cone to bend to allow the final connection tabs to insert into the remaining connection slots. Secure round connections with 5/16”-18 X 3/4” hex bolts, 5/16” flat washers, and 5/16”-18 serrated nuts leaving the slots closet to the larger diameter open at this time. A washer should be used on the inside and outside of each connection. BOLT HEADS SHOULD BE ON THE OUTSIDE OF THE CONE! 15. Using 2 people lift the cone and butterfly assembly and slide OVER THE BUTTERFLY BUT UNDER THE MOUNTING BRACKET! Push onto the assembly until slots bottom out on the mounting bolts. Twist cone to lock into place then completely tighten lock nuts to secure.
Hog Slat Inc. Newton Grove, NC USA June 2023 15 Air Storm Fans 16. Drill a ¼” hole at the 12 o’clock position in the cone assembly at the butterfly ring to the exit side of the fan. Then insert end of supplied stainless steel cable through hole at the 12 o’clock position just before the butterfly, secure end above cone with supplied cable clamp. 17. Insert grill guard into cone and secure each connection with a 5/16”-18 X 1” hex bolt, (2) 5/16” flat washers, and a 5/16”-18 serrated flange nut from hardware bag number 13. Leave Top and Bottom connection open at this time.
Hog Slat Inc. Newton Grove, NC USA June 2023 16 Air Storm Fans Use hardware form bag 17 for the top and bottom connection of the fan exit guard. Pull stainless steel cable until tight and having it exit at the 6 o’clock position of the cone. Wrap stainless steel cable around bolt twice and tighten to secure. Cable should be tight but should not be applying force to the assembly. Exit guards should be modified accordingly to still provide maximum protection.
Hog Slat Inc. Newton Grove, NC USA June 2023 17 Air Storm Fans 18. From the interior of the house assemble interior guard as shown with supplied zip ties. (8) total zip ties should be used securing all 8 corners. 19. Mount cup hooks to support interior guard, cup hooks can be found in hardware bag number 19. 4 should be used across the top capturing the corners with 2 supports in the middle. The remaining 2 should be located on the bottom right and bottom left corners to secure the interior guard. Depending on spacing chosen for fans slight, modifications may have to be made to the mounting of the interior guard. THIS COMPLETES THE HOUSING ASSEMBLY OF THE FAN
Hog Slat Inc. Newton Grove, NC USA June 2023 18 Air Storm Fans Wiring To access motor, turn shutter retainer clips so shutter can be removed. Again, make sure that power is disconnected from system prior to servicing. Always ensure proper prop rotation after install or motor replacement. During operation air should be directed from inside the building to the outside. ALWAYS FOLLOW MOTOR WIRING DIAGRAM PROVIDED ON MOTOR! ELECTRICAL SHOCK HAZARD! • Motor replacement and the associated wiring changes should only be made by qualified and properly trained individuals. • Failure to follow the above warning can cause improper equipment function, premature failure of equipment or electrical shock, leading to property damage or personal injury. Single Phase (230 Volt Wiring) Three Phase (230/460 Wiring) -note rotation, if change is needed swap any leg (L1, L2, or L3).
Hog Slat Inc. Newton Grove, NC USA June 2023 19 Air Storm Fans General Installation Notes: Make sure that power is disconnected from system prior to servicing. Installation of this equipment and related OEM equipment should be in accordance with these instructions, OEM’s installation instructions and local codes (if applicable). Failure to follow specified instructions may cause damage to equipment and/or personal injury or death. Take special note of any Warnings or Safety Decals on the equipment and in manuals. Always wear protective clothing and any applicable Personal Protective Equipment (Safety Glasses and/or Ear Plugs) when working with the equipment. Discarded materials, equipment and boxes should be recycled in accordance with local and national codes. Safety Instructions: Read all safety messages in this manual and on equipment safety decals. Follow recommended precautions and safe operating practices. Ground all electrical equipment for safety. Ground all non-current carrying metal parts to guard against electrical shock. Pre-Operation Assessment Before beginning fan operation, please follow the below checklist to ensure that: Fan power cord securely connected to a good power supply. All safety labels are visible to personnel that will work in the area. Exit wire guard and inlet shutter are in place and secured to the fan housing. No foreign objects are protruding through the fan housing. Operation At all times during operation, fan orifice should be free of debris. In the event any component of the fan is compromised, discontinue use immediately and contact your local Hog Slat representative.
Hog Slat Inc. Newton Grove, NC USA June 2023 20 Air Storm Fans Maintenance In order to begin any maintenance or service to the fan, power must be turned OFF and all moving parts must come to a complete STOP before accessing. All parts inside of the fan housing are accessed by removing the exit wire guard and inlet shutter. Once service is complete, clean excessive build-up from parts. Excessive dust and dirt on parts can cause vibration in the propeller and overheating of the motor. Before beginning operation again, ensure that all safeguards are back in place and all foreign objects are free from the area. DURING MAINTENANCE AND OPERATION THE FOLLING MUST BE MAINTAINED TO ENSURE PROPER PERFORMANCE AND TO EXTEND USABLE COMPONENT LIFE. • DRIVE COMPONENTS ALIGNMENT o Proper alignment of pulleys, tension arms, etc.. is required to avoid excessive belt and drive component wear. Failure to maintain correct alignment during maintenance will void warranty of drive components A straight edge or laser alignment device should be utilized to check for alignment of drive components [! IMPORTANT ! If for any reason drive system components are removed/replaced or loosened; it is important to ensure that components are properly realigned to achieve proper performance and longevity ] • BELT TENSION AND DIRECTION (when applicable) o Proper belt tension and direction is critical to avoid excessive belt and drive component wear. Failure to maintain correct belt tension during operation or maintenance will void warranty of drive components. Supplied belt tensioner should be used to ensure proper belt tension. Correct operation occurs when the tension arm is operating at the second indicator mark Correct belt direction (when applicable) can be determined by an indicator on the belt notating desired rotation direction
Hog Slat Inc. Newton Grove, NC USA June 2023 21 Air Storm Fans • BEARING LUBRICATION (when applicable) o Proper bearing lubrication is critical to ensure adequate operating life of bearings. Failure to follow a lubrication schedule during operation will void warranty of bearings Bearings should be greased every 4-6 months (where applicable) Premium grease is recommended Use of electric grease gun is strictly prohibited and will void warranty of bearings • PROPER V GROOVE MAINTAINCE o Proper V groove dimensions are critical to maintaining performance and eliminating excessive belt wear. Failure to maintain proper V groove dimension will void warranty of drive components. V belt gauges should be utilized to check for correct V groove dimensions. Alternatively belts location on pulley can be used. Correct dimensions should allow belt to ride slightly above the outermost diameter of the pulleys, if belt rides below outermost diameter, pulley(s) should be changed.
Hog Slat Inc. Newton Grove, NC USA June 2023 22 Air Storm Fans Please see below for direction regarding applying grease to pillow block bearings UCP20516G5 (Bearings shipped on Grower Select Fans) Grease Amount: (1) Stroke on most standard grease guns or 0.8 grams * Volume dispensed per stroke should be verified with grease gun manufacturer Grease Interval: Every 300 Hours of Operation Type of Grease: Lithium Based NLGI No.2 Note: ELECTRIC OR BATTERY POWERED GREASE GUNS SHOULD NOT BE USED AND MAY VOID WARRANTY! Troubleshooting Trouble Possible Cause(s) Corrective Action Excessive noise Worn motor bearing. Replace Damage to fan blade Replace prop Loose fasteners on motor or housing Tighten fasteners Excessive vibration Fan blade is out of balance due to dirt build-up. Clean entire unit Fan blade is out of balance due to damage Replace prop Insufficient airflow Intake or exhaust guards clogged with debris Clean entire unit Intake or exhaust blocked by foreign object Remove object from airflow path Fan won’t operate Open power supply circuit. Check wiring and reset circuit breaker Defective motor Reset motor, repair, or replace Motor overheats and nuisance trips Improper airflow due to clogged Inlet/Outlet Clean entire unit Motor or Fan prop has excessive debris build-up Clean entire unit
Hog Slat Inc. Newton Grove, NC USA June 2023 23 Air Storm Fans Performance Hog Slat Inc. takes great pride in supplying our customers with fans that meet or exceed their performance numbers. This is achieved by testing fans from the production line and continually working to maintain consistency in test data. HSPCT-01090 AS-36EBDBPG Static Pressure (in.H2O) Airflow (cfm) Rpm Volts Amps Watts cfm/Watt 0.00 12240 756 230.0 2.92 690 17.7 0.05 12010 755 230.1 2.96 698 17.2 0.10 10910 754 230.2 3.00 705 15.5 0.15 9230 753 230.3 3.04 713 12.9 0.20 7260 752 230.2 3.08 720 10.1 0.25 5320 751 230.5 3.12 728 7.3 0.30 3690 750 230.6 3.16 735 5.0 HSPCT-01117 AS-36EBDBPG-HV Static Pressure (in.H2O) Airflow (cfm) Rpm Volts Amps Watts cfm/Watt 0.00 16250 968 231.3 6.12 1420 11.6 0.05 15470 968 231.3 6.20 1440 10.8 0.10 14520 968 231.3 6.28 1459 9.9 0.15 13650 967 231.3 6.36 1479 9.1 0.20 12660 967 231.3 6.44 1499 8.3 0.25 11490 966 231.3 6.52 1518 7.5 0.30 10060 966 231.3 6.60 1538 6.8
Hog Slat Inc. Newton Grove, NC USA June 2023 24 Air Storm Fans Exploded Diagrams/Replacement Parts AS-36EBDBPG Item Key Replacement Part Number Description 1 WS900-36A Prop 36" Galvanized 3 Blade 1" Shaft 5 UCP20516G5 Bearing 1" Pillow Block Standard 2 Set Screws 7 HS9010C Motor 1 HP 1725 RPM 115/208-230V 1Ph 60/50Hz 56Fr 5/8" Shaft 8 HS903-3 Tensioner Rotary Assembly With Splash Guards 9 PAK4158 Pulley AK41-5/8 10 PAK941 Pulley AK94-1 14 WS-901-36U Butterfly Assembly 36" Fan Unpainted 16 AS-36305P Panel Cone 36" Poly Black 17 HS902-36E Guard Exit 36" Windstorm SW Fan N/S HSAX48 Belt V 1/2" X 50" Cogged N/S HS903-14 Spring Butterfly 52" Windstorm N/S WS-HW36G Kit Hardware AS-36EBDBPG For OSHA compliant guards, contact your local Hog Slat representative.
Hog Slat Inc. Newton Grove, NC USA June 2023 25 Air Storm Fans Exploded Diagrams/Replacement Parts AS-36EBDBPG-HV Item Key Replacement Part Number Description 1 WS900-36A Prop 36" Galvanized 3 Blade 1" Shaft 5 UCP20516G5 Bearing 1" Pillow Block Standard 2 Set Screws 7 HS9019 Motor 1-1/2 HP 1725 RPM 50/60 Hz 1 Ph 208-230V 1.2 SF 8 HS903-3 Tensioner Rotary Assembly With Splash Guards 9 PAK5658 Pulley AK56 5/8" Bore 10 PAK991 Pulley AK99-1 14 WS-901-36U Butterfly Assembly 36" Fan Unpainted 16 AS-36305P Panel Cone 36" Poly Black 17 HS902-36E Guard Exit 36" Windstorm SW Fan N/S HSAX51 Belt V 1/2'' X 53'' Cogged N/S HS903-14 Spring Butterfly 52" Windstorm N/S WS-HW36G-HV Kit Hardware AS-36EBDBPG-HV For OSHA compliant guards, contact your local Hog Slat representative.
Hog Slat Inc. Newton Grove, NC USA June 2023 26 Air Storm Fans THIS PAGE INTENTIONALLY LEFT BLANK
Hog Slat Inc. Newton Grove, NC USA June 2023 27 Air Storm Fans Hog Slat Limited Warranty Hog Slat warrants products to be free from defects in material or workmanship for a period of twenty-four (24) months from the date of original purchase. Hog Slat will credit, repair, or replace, at its option any product deemed defective within this time period. Labor costs associated with the replacement or repair of the product are not covered by the Seller/Manufacturer. Conditions and Limitations 1. The product must be installed by and operated in accordance with the instructions published by the Seller/Manufacturer or Warranty will be void. 2. Warranty is void if all components are not original equipment supplied by the Seller/Manufacturer. 3. This product must be purchased from and installed by an authorized retailer/distributor or certified representative thereof or the Warranty will be void. 4. Malfunctions or failure resulting from misuse, abuse, negligence, alteration, accident, or lack of proper maintenance shall not be considered defects under the Warranty. 5. This Warranty applies only to components/systems for the care of poultry and livestock. Other applications in industry or commerce are not covered by this Warranty. 6. This Warranty applies only to the Original Purchaser of the product. The Seller/Manufacturer shall not be liable for any Consequential or Special Damage which any purchaser may suffer or claim to suffer as a result of any defect in the product. “Consequential” or “Special Damages” as used herein include, but are not limited to, lost or damaged products or goods, costs of transportation, lost sales, lost orders, lost income, increased overhead, labor and incidental costs and operational inefficiencies. THIS WARRANTY CONSTITUTES THE SELLER/MANUFACTURER’S ENTIRE AND SOLE WARRANTY AND THIS MANUFACTURER EXPRESSLY DISCLAIMS ANY AND ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, EXPRESS AND IMPLIED WARRANTIES AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSES SOLD AND DESCRIPTION OR QUALITY OF THE PRODUCT FURNISHED HEREUNDER. Hog Slat Retailers/Distributors are not authorized to modify or extend the terms and conditions of this Warranty in any manner or to offer or grant any other warranties for GrowerSelect products in addition to those terms expressly stated above. An officer of Hog Slat must authorize any exceptions to this Warranty in writing. The Seller/Manufacturer reserves the right to change models and specifications at any time without notice or obligation to improve previous models.
Hog Slat Inc. Newton Grove, NC USA June 2023 28 Air Storm Fans This equipment must be installed in accordance with all State and Local Codes and applicable Regulations which should be followed in all cases. Authorities having jurisdiction should be consulted before installations are made. Hog Slat, Inc. PO Box 300 Newton Grove, NC 28366 Phone: (910) 594-0219 Fax: (910) 594-1392 www.hogslat.com Copyright © 2022 by Hog Slat, Inc. Part Number: HSManual-263 Rev A1 HSART-626 Market: Hog & Poultry
hogslat.comRkJQdWJsaXNoZXIy MTA3MzU=