Hog Slat Inc. Newton Grove, NC USA June 2020 1 Feed Systems HSFC20 Flat Chain Single Line Unloader Vertical Extension Hopper Installation
Hog Slat Inc. Newton Grove, NC USA June 2020 2 Feed Systems NOTES:
Hog Slat Inc. Newton Grove, NC USA June 2020 3 Feed Systems GENERAL INSTALLATION NOTES: Make sure that power is disconnected from system prior to servicing. Installation of this equipment and related OEM equipment should be in accordance with these instructions, OEM’s installation instructions and local codes (if applicable). Failure to follow specified instructions may cause damage to equipment and/or personal injury or death. Take special note of any Warnings or Safety Decals on the equipment and in manuals. Always wear protective clothing and any applicable Personal Protective Equipment (Safety Glasses and/or Ear Plugs) when working with the equipment. Discarded materials, equipment and boxes should be recycled in accordance with local and national codes. SAFETY INSTRUCTIONS Read all safety messages in this manual and on equipment safety decals. Follow recommended precautions and safe operating practices. Always keep safety decals in good condition and replace missing or damaged decals. SAFETY DECALS AND WARNING LABELS None Applicable
Hog Slat Inc. Newton Grove, NC USA June 2020 4 Feed Systems COMPONENT LAYOUTS
Hog Slat Inc. Newton Grove, NC USA June 2020 5 Feed Systems SINGLE LINE UNLOADER VERTICAL EXTENSION HOPPER PARTS LIST ITEM QTY PART NUMBER DESCRIPTION 1 4 HSFC20-2 HOPPER, EXTENSION, SIDE PANEL 2 1 HSFC20-3 HOPPER, EXTENSION, BASE PLATE 3 2 HSFC20-1 HOPPER, EXTENSION, TOP HALF 4 28 60500 BOLT, HEX, 1/4 –20 X 1/2, ZINC 5 28 60596 WASHER, LOCK 1/4” ZINC 6 28 60570 NUT, HEX 1/4 -20 ZINC 7 12 80518 SCREW, SELF DRILLING #10-16 X 5/8” ZINC 8 1 HSLABEL-053 LABEL PRODUCT GROWER SELECT NEST INSTALLATION / OPERATION 1. Mount 4 side plates (HSFC20-2) to base plate (HSFC20-3) with 8 hex bolts, lock washers, and hex nuts (60500, 60596, and 60570). 2. Use 4 self drilling screws (80518) to mount 2 top half plates (HSFC20-1) together. Then use 8 self drilling screws (80518) to mount top assembly to side plates. 3. Align completed hopper extension assembly to top of hopper and bolt down using either 1/4-20 bolts with lock washers or #10 self drilling screws (8 total required). 4. Place label (HSLABEL-053) to one side of panel. .
Hog Slat Inc. Newton Grove, NC USA June 2020 6 Feed Systems THIS PAGE INTENTIONALLY LEFT BLANK
Hog Slat Inc. Newton Grove, NC USA June 2020 7 Feed Systems Hog Slat Limited Warranty Hog Slat warrants products to be free from defects in material or workmanship for a period of twenty-four (24) months from the date of original purchase. Hog Slat will credit, repair, or replace, at its option any product deemed defective within this time period. Labor costs associated with the replacement or repair of the product are not covered by the Seller/Manufacturer. Conditions and Limitations 1. The product must be installed by and operated in accordance with the instructions published by the Seller/Manufacturer or Warranty will be void. 2. Warranty is void if all components are not original equipment supplied by the Seller/Manufacturer. 3. This product must be purchased from and installed by an authorized retailer/distributor or certified representative thereof or the Warranty will be void. 4. Malfunctions or failure resulting from misuse, abuse, negligence, alteration, accident, or lack of proper maintenance shall not be considered defects under the Warranty. 5. This Warranty applies only to components/systems for the care of poultry and livestock. Other applications in industry or commerce are not covered by this Warranty. 6. This Warranty applies only to the Original Purchaser of the product. The Seller/Manufacturer shall not be liable for any Consequential or Special Damage which any purchaser may suffer or claim to suffer as a result of any defect in the product. “Consequential” or “Special Damages” as used herein include, but are not limited to, lost or damaged products or goods, costs of transportation, lost sales, lost orders, lost income, increased overhead, labor and incidental costs and operational inefficiencies. THIS WARRANTY CONSTITUTES THE SELLER/MANUFACTURER’S ENTIRE AND SOLE WARRANTY AND THIS MANUFACTURER EXPRESSLY DISCLAIMS ANY AND ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, EXPRESS AND IMPLIED WARRANTIES AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSES SOLD AND DESCRIPTION OR QUALITY OF THE PRODUCT FURNISHED HEREUNDER. Hog Slat Retailers/Distributors are not authorized to modify or extend the terms and conditions of this Warranty in any manner or to offer or grant any other warranties for GrowerSelect products in addition to those terms expressly stated above. An officer of Hog Slat must authorize any exceptions to this Warranty in writing. The Seller/Manufacturer reserves the right to change models and specifications at any time without notice or obligation to improve previous models.
Hog Slat Inc. Newton Grove, NC USA June 2020 8 Feed Systems This equipment must be installed in accordance with all State and Local Codes and applicable Regulations which should be followed in all cases. Authorities having jurisdiction should be consulted before installations are made. Hog Slat, Inc. PO Box 300 Newton Grove, NC 28366 Phone: (910) 594-0219 Fax: (910) 594-1392 www.hogslat.com Copyright © 2020 by Hog Slat, Inc. Part Number: HSMANUAL-213 Revision IR Market - Poultry Product Group - Grower Select
hogslat.comRkJQdWJsaXNoZXIy MTA3MzU=