Table of Contents 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

Hog Slat Feed Bin Installation Operation English Manual

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 Feed Bins Feed Bin Installation and Operation Manual 6’, 7’, 9’, and 12’ Diameter Feed Bins

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 2 Feed Bins Table of Contents Hog Slat General Page............................................................................................................................................................... 3 Support Information ................................................................................................................................................................ 3 Hardware Identification ........................................................................................................................................................... 3 Safety .......................................................................................................................................................................................4-6 Recognize Safety Information ............................................................................................................................................. 4 Warning Label......................................................................................................................................................................... 4 General Safety Statement....................................................................................................................................................... 4 Hazards .................................................................................................................................................................................. 6 Alternate Anchors………………………………………………………………………………………………………………………..6 Foundation.............................................................................................................................................................................7-11 6 Foot Tank............................................................................................................................................................................. 7 7 Foot Tank............................................................................................................................................................................. 8 9 Foot Tank............................................................................................................................................................................. 9 12 Foot Tank......................................................................................................................................................................... 10 Sidewall Sheet Gauge Charts.................................................................................................................................................. 11 Sidewall Sheet Assembly ...................................................................................................................................................12-13 Top Ring ............................................................................................................................................................................... 12 Middle Rings ......................................................................................................................................................................... 13 Bottom Rings ........................................................................................................................................................................ 13 Roof Panel Assembly............................................................................................................................................................... 14 Hopper Assembly..................................................................................................................................................................... 15 Leg Assembly........................................................................................................................................................................... 16 Brace Assembly ....................................................................................................................................................................... 17 Cross Brace Assembly.......................................................................................................................................................... 17 Hopper Brace Assembly ....................................................................................................................................................... 17 Lid Assembly.......................................................................................................................................................................18-19 Ladder Assembly ................................................................................................................................................................20-22 Ladder Stand Off................................................................................................................................................................... 20 Vertical Ladder Assembly ..................................................................................................................................................... 21 Roof Ladder Assembly.......................................................................................................................................................... 22 Ladder Handrail Assembly.................................................................................................................................................... 22 Safety Cage Assembly........................................................................................................................................................23-25 Pnuematic Fill Assembly ....................................................................................................................................................26-27 Erecting the Feed Bin .............................................................................................................................................................. 28 Grounding ............................................................................................................................................................................. 28 Ladder Matrix............................................................................................................................................................................ 29 Component Listing..............................................................................................................................................................30-41 6 Foot Tank......................................................................................................................................................................30-31 7 Foot Tank......................................................................................................................................................................32-34 9 Foot Tank......................................................................................................................................................................35-37 12 Foot Tank....................................................................................................................................................................38-40 Lid Assembly ........................................................................................................................................................................ 41 Tank Specification.................................................................................................................................................................... 42 Hog Slat Limited Warranty ...................................................................................................................................................... 43 Company Info ........................................................................................................................................................................... 44

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 3 Feed Bins Hog Slat General Page General Installation Notes: Installation of this equipment and related OEM equipment should be in accordance with these instructions, OEM’s installation instructions and local codes (if applicable). Failure to follow specified instructions may cause damage to equipment and/or personal injury or death. Take special note of any Warnings or Safety Decals on the equipment and in manuals. Always wear protective clothing and any applicable Personal Protective Equipment (Safety Glasses and/or Ear Plugs) when working with the equipment. Discarded materials, equipment and boxes should be recycled in accordance with local and national codes. Support Information Hog Slat Feed Bins are designed for grains and/or free flowing materials. Using this equipment for any other purpose or in a way not within the operating recommendations specified in this Manual will void the Warranty and may cause injury or death. Identification of Hardware: No hardware substitutions are permitted unless noted. WARNING! Grade 8.2 Markings Do NOT place feed bins in direct air flow of exhaust fans. HS712 5/16” x 1” Hex Head Bin Bolt HS714 5/16” x 3/4” Truss Head Bin Bolt HS722 Serrated Flange Nut

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 4 Feed Bins Safety Warning Labels Warning Decals have been placed on the equipment to warn of potentially dangerous situations. Care should be taken to keep this information intact and easy to read at all times. Replace missing or damaged safety signs. Safety–Alert Symbol This is a safety–alert symbol. When you see this symbol on your equipment, be alert to the potential for personal injury. Hog Slat equipment is designed to be installed and operated as safely as possible...however, hazards do exist. Important Information Symbol This is an Information–alert symbol. When you see this symbol throughout this installation manual, be sure to read the information provided. Safety decals should be read and understood thoroughly by individuals within the local area of the Feed System. Should a decal be missing or damaged, please contact Hog Slat Inc. for a free replacement: Hog Slat Inc. 206 Fayetteville St. Newton Grove, NC 28366 Toll Free: 800-949-4647 Local: 910-594-0219 It is a matter of extreme SAFETY importance that your bins are NOT placed where feed trucks, augers or other equipment may accidentally come in contact with electric power lines, control boxes or other electrical hazards which may result in serious injury or death! Contact your power company before construction for a review of proper line clearance. This could save you the expense of moving facilities later. DANGER!

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 5 Feed Bins This safety decal should be represented and visible on the inside of the ladder rail at eye-level. This safety decal should be represented and visible on the inside of the Peak Ring (Fill-Hole) when Lid is in the open position.

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 6 Feed Bins Thereare SuffocationHazards inFlowingGrainandFeed! Never enter a bin of flowing feed, grain, or other material. Failure to follow these instructions will result in death or serious injury From the time the auger starts, you have 2-3 seconds to react. In 4-5 seconds, you are trapped. After 22 seconds, you are completely covered. Anchor Options DANGER! Anchor bolt 5/8" x 8" (203 mm) bolt with an 1/8" thick x 1-3/4" O.D. washer on head.

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 7 Feed Bins Foundation 6’ Diameter Feed Bins # of Rings Slab Thickness (T) Concrete Volume Wire Mesh Area Qty of Legs Square 1-5 11" [279 mm] 2.2 Cu. Yards [1.68 Cu. Meters] 60 Sq. Ft. [5.57 Sq. Meters] 4 Round 1-5 11" [279 mm] 1.7 Cu. Yards [1.31 Cu. Meters] 55 Sq. Ft. [5.11 Sq. Meters] 4 Square Foundation Round Foundation 1. Foundation recommendations are based on 3500 lbs / ft2 allowable soil bearing capacity. 2. Foundation recommendations are based on a minimum compressive strength of 3000 PSI at 28 days. 3. The foundation site must be well drained and free of vegetation and debris. 4. The foundation should be level within 1/4" overall and within +/-1/8” in any 10 foot length along the anchor bolt circle. 5. Material estimates do not include allowance for shrinkage and waste. 6. These layouts are recommendations for Hog Slat tanks only. Consult Hog Slat engineering for special tank foundations. 6” Maximum above Grade 6” Maximum above Grade

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 8 Feed Bins 7’ Diameter Feed Bins # of Rings Slab Thickness (T) Concrete Volume Wire Mesh Area Qty of Legs Square 1-6 13" [330 mm] 3.3 Cu. Yards [2.52 Cu. Meters] 80 Sq. Ft. [7.43 Sq. Meters] 4 Round 1-6 13" [330 mm] 2.6 Cu. Yards [1.91 Cu. Meters] 65 Sq. Ft. [6.04 Sq. Meters] 4 1. Foundation recommendations are based on 3500 lbs / ft2 allowable soil bearing capacity. 2. Foundation recommendations are based on a minimum compressive strength of 3000 PSI at 28 days. 3. The foundation site must be well drained and free of vegetation and debris. 4. The foundation should be level within 1/4" overall and within +/-1/8” in any 10 foot length along the anchor bolt circle. 5. Material estimates do not include allowance for shrinkage and waste. 6. These layouts are recommendations for Hog Slat tanks only. Consult Hog Slat engineering for special tank foundations. Square Foundation Round Foundation 6” Maximum above Grade 6” Maximum above Grade

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 9 Feed Bins 9’ Diameter Feed Bins # of Rings Slab Thickness (T) Concrete Volume Wire Mesh Area Qty of Square 1-7 13" [330 mm] 4.9 Cu. Yards [4.85 Cu. Meters] 125 Sq. Ft. [11.61 Sq. Meters] 6 Round 1-7 13" [330 mm] 3.8 Cu. Yards [2.91 Cu. Meters] 100 Sq. Ft. [9.29 Sq. Meters] 6 1. Foundation recommendations are based on 3500 lbs / ft2 allowable soil bearing capacity. 2. Foundation recommendations are based on a minimum compressive strength of 3000 PSI at 28 days. 3. The foundation site must be well drained and free of vegetation and debris. 4. The foundation should be level within 1/4" overall and within +/-1/8” in any 10 foot length along the anchor bolt circle. 5. Material estimates do not include allowance for shrinkage and waste. 6. These layouts are recommendations for Hog Slat tanks only. Consult Hog Slat engineering for special tank foundations. Square Foundation Round Foundation 6” maximum above Grade 6” maximum above Grade

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 10 Feed Bins 12’ Diameter Feed Bins # of Rings Slab Thickness (T) Concrete Volume Wire Mesh Area Qty of Square 1-5 15" [381 mm] 9.1 Cu. Yards [6.93 Cu. Meters] 196 Sq. Ft. [18.21 Sq. Meters] 8 Square 6-7 16" [406 mm] 9.7 Cu. Yards [7.40 Cu. Meters] 196 Sq. Ft. [18.21 Sq. Meters] 8 Round 1-5 15" [381 mm] 7.1 Cu. Yards [5.45 Cu. Meters] 155 Sq. Ft. [14.40 Sq. Meters] 8 Round 6-7 16" [406 mm] 7.6 Cu. Yards [5.81 Cu. Meters] 155 Sq. Ft. [14.40 Sq. Meters] 8 1. Foundation recommendations are based on 3500 lbs / ft2 allowable soil bearing capacity. 2. Foundation recommendations are based on a minimum compressive strength of 3000 PSI at 28 days. 3. The foundation site must be well drained and free of vegetation and debris. 4. The foundation should be level within 1/4" overall and within +/-1/8” in any 10 foot length along the anchor bolt circle. 5. Material estimates do not include allowance for shrinkage and waste. 6. These layouts are recommendations for Hog Slat tanks only. Consult Hog Slat engineering for special tank foundations. 6” maximum above Grade 6” maximum above Grade Square Foundation Round Foundation

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 11 Feed Bins Side Wall Sheet Gauge Chart Tank Gauge 6' - 60° Hopper BFT 6'-1 Ring 20 BFT 6'-2 Ring 20-20 BFT 6'-3 Ring 18-20-20 BFT 6'-4 Ring 18-20-20-20 7' - 67° Hopper BFT 7'-1 Ring 20 BFT 7'-2 Ring 18-20 BFT 7'-3 Ring 18-20-20 BFT 7'-4 Ring 18-18-20-20 BFT 7'-5 Ring 16-18-18-20-20 BFT 7'-6 Ring 14-16-18-18-20-20 9' - 60° Hopper BFT 9'-1 Ring 20 BFT 9'-2 Ring 20-20 BFT 9'-3 Ring 20-20-20 BFT 9'-4 Ring 18-18-20-20 BFT 9'-5 Ring 16-18-18-20-20 BFT 9'-6 Ring 14-16-18-18-20-20 BFT 9'-7 Ring 12-12-16-16-18-20-20 12' - 60° Hopper BFT 12'-1 Ring 18 BFT 12'-2 Ring 14-20 BFT 12'-3 Ring 14-18-20 BFT 12'-4 Ring 14-16-20-20 BFT 12'-5 Ring 12-16-18-20-20 BFT 12'-6 Ring 12-14-16-18-20-20 BFT 12'-7 Ring 12-12-14-16-18-20-20 Sheet Gauge Color Chart 20ga Red 18ga Orange 16ga Blue 14ga Green 12ga Black 10ga Yellow Side wall sheets are color coded on edges for gauge identification. Simply match the gauge color with the number.

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 12 Feed Bins Side Wall Sheet Assembly 1. Identify the 3 lightest corrugated Top sheets (color coded), or by the top row of holes being spaced 3 1/8” apart. The top sheet will also have a decal. 2. Apply the roll caulking (HS721) to the inside of the side wall sheets, (Vertical Seam) along each side the holes (except top sheet with 3 1/8” center holes, this caulk will be added on the roof panels). Be sure to caulk all seams along both sides of the holes to form a good seal and prevent leaking! 3. Place the caulked end over the un-caulked end of each adjacent hopper sheet. 4. Assemble ends with HS712 bin bolts and HS722 Hex Nuts (Hex nuts on inside of bin). Continue inserting Bin Bolts and Hex Nuts to all the holes along the vertical seam as you assemble the ring. Do not tighten until all sheets of each ring are assembled. Tighten Hex nuts Only! Tightening by the bolt head may result in seal failure. Sheet Gauge Color Chart 20ga Red 18ga Orange 16ga Blue 14ga Green 12ga Black 10ga Yellow Roll Caulking (HS721)

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 13 Feed Bins 5. Add 2 rows of roll caulk to the top-outside edge of the Mid Sidewall sheet on each side of holes. 6. Place (1) Mid Sidewall sheet on inside of the assembled top ring making sure the mid sidewall sheet ends are at the center of the first top sheet and holes align, as illustrated. Use the HS712 Hex Bin Bolt and the HS722 Hex Nuts in each hole to attach. 7. After completing the second ring you should lay assembly on its side so hoppers can be rolled easily to help make remaining assembly easier as shown. On 5 and 6 ring bins you will need to align leg holes with bottom ring leg holes. 8. Tighten horizontal seams by starting in center of hopper sheet and working toward ends as shown with blue arrows. When all hopper sheets are assembled you should have the heaviest corrugation on the bottom, the decal sheet on top, and with each vertical seam staggered. Tighten bin bolts from center of panels working outward Heaviest sheet with Drip Lip on Bottom Vertical Seams Top Sheet center Roll Caulk

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 14 Feed Bins Roof Panels The roof and sidewall ladders are centered between top sheet vertical seams 1. Begin caulking roof panels along the inside edge of one side and the inside edge of the top corrugated flange, as shown. 2. Align the center of the first roof panel with any of the top sidewall sheet vertical seams. 3. Assemble roof decks over the top of the previous panel in a counterclockwise direction. Use the HS712 Hex Bin Bolts and the HS722 Hex Nuts. Keep bolt heads to the outside. 4. After determining the ladder location, add the two Roof Ladder Support braces at each side of the one roof panel that the ladder will be centered on. 5. After all roof panels are installed, caulk the inside flange of the peak ring and attach to roof using HS712 Hex Bin Bolts and the HS722 Hex Nuts Inside Inside Caulk these inside edges of each roof panel (with slot at flange corner) Inside 3/8 x1/2 slot = Ladder Location Options * * * 6’ & 7’ Diameter * * * 9’ Diameter Ladder support Brackets Bolt to the inside of Feed Bin 12’ Diameter * * * *

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 15 Feed Bins Hopper Panels 1. Begin caulking around the inside of the bottom row of holes on the bottom ring of corrugated side wall sheets. 2. Caulk the hopper panel sheets along the vertical edge with the bend towards the outside. Caulk all hoppers panels on the same inside edge and apply to both sides of holes. 3. Align the center of the first hopper panel section with any of the vertical seams on the top ring and assemble to inside of corrugated sidewall sheets using HS712 Hex Bin Bolts and the HS722 Hex Nuts. 4. Continue around until all but one hopper panel are assembled and bolts tightened. Hopper Reinforcement Angle GST-HR960 for 9’ 3-6 ring tanks GST-HR1260 for 12’ 3-6 ring tanks Caulk 5. Before installing the last hopper panel. Apply caulk on both sides of the holes on the hopper collar and insert into the flanged end of the assembled hopper panels. 6. Bolt the hopper collar to the hopper panel flange using HS714 Truss head bins bolts and HS722 Flange nuts. Truss heads to the inside. Vertical Seam 3/8 Round Hole

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 16 Feed Bins Legs 1. Assemble top and bottom Leg Base Plates to each leg. 2. The bin leg attaches to the (11) leg holes in the bottom ring. The bin legs with 23 holes will require the bottom two rings. 3. Align holes with Drift Pin from outside of bin. Hand tighten the HS712 Hex Bin Bolts and the HS722 Flange nuts on all holes. Keep bolt heads to the Inside of tank. 4. Roll the bin to assemble each leg until all the legs are complete. Tighten all nuts secure. 5. Before person exits bin, have them check for missing bolts by darkening bin and looking for light thru open holes. Leg

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 17 Feed Bins Leg X-Brace / Hopper Brace 1. Install the Hopper Braces and X-Braces to Legs using 3/8 x 1'' Hex Head Gr. 8 Bolts and 3/8'' Nuts. 2. The Longest tab of the x-braces should be to the top. 3. Attach hopper braces to the leg and secure. 4. Align the hopper end of the brace to the nearest hole in the hopper collar and secure. Do not tighten X-brace’s until all hopper braces have been installed and tightened. Install with the Flange pointing downward as shown 64 7/16 26 1/16

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 18 Feed Bins Lid Assembly Installation 1. Thread the HS719 5/16-20 nut onto the HS804 Eyebolt and thread the eyebolt completely into the lid assembly using the HS719 as a jam nut. 2. Place lid assembly over peak ring and loosely secure with the 607065 3/8” x 3.5” Carriage bolt and 60682 Lock nut (tighten the band together by hand so the lid will rotate freely). You will tighten at step 9. 3. Slide the spring onto the Pivot Bushing and snap the loop over the 3/8 pivot rod. 4. Using pliers grip the outer end of the spring and rotate around until the end of the spring end rod is aligned with the bushing slot. Slide the spring end rod completely into the slot. 5. Rotate lid assembly as needed to access other spring and repeat step 4 Spring Loop 607065 Carriage Bolt HS804 Eyebolt The Clamp Band must be between the formed ribs. 60682 Locknut Formed Ribs Notice: The lids are shipped with the springs uninstalled for ease of installation HS719 5/16-20 Nut Spring End Rod GST-LD3062R GST-LD3062L

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 19 Feed Bins 6. Thread the Pull Cable loop up through the grommet at the eave and attach to the lid eyebolt using the GST-LD3033 carabiner. 7. With the lid in full open position - Slip the Lock Collar over the cable and tighten just under the GST-LD1011 Guide bracket to lock the lid in the open position. 8. Loop the cable through the GST-LD1013 tube until the desired height and secure with 617321 Cable Clamp. Trim off excess cable. 9. Rotate lid to align the wheel and eyebolt with the grommet attached to roof eave and tighten completely. GST-LD1013 tube 617321 Cable Clamp GST-LD2041 Lock Collar (Set with lid at full open) The Lid Eyebolt must be aligned with the grommet. Do not over tighten Clamp Band to where the flanges are bent inward. GST-LD3033 Carabiner Clip GST-LD1011 Guide

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 20 Feed Bins Ladder Top mount brackets GST-LS6407 (9’ tank) GST-LS6408 (6’ tank) GST-LS6409 (7’ tank) GST-LS6410 (12’ tank) Ladder Assembly 1. Attach the roof ladder stand-off brackets at the third hole down from the collar. Centered on the Roof Panel that has the ladder reinforcement bracket. 2. Attach the Ladder top mount brackets (left and right handed) at the fourth hole from each roof seam (5 holes in between and centered on roof panel). 3. Mount the curved ladder support channel to the legs through the nearest available hole to the X-brace mounts (Using the HS716 3/8” x 1” Gr8 bolts and HS724 3/8” serrated flange nut). 4. Continue to mount the GST-LS6403 vertical ladder mount bracket to each horizontal sidewall seam and at the Curved ladder support channels immediately below the top mount brackets (in-line) Roof stand-off bracket GST-LS6405 (6’, 9’, & 12’ tanks) GST-LS6411 (7’ tank) Ladder Top mount brackets GST-LS6406 (Right) GST-LS6412 (Left) Ladder Standoff Bracket GST-LS6403

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 21 Feed Bins 5. Starting at the top ladder mount brackets, attach the ladder and the corner bracket at the same time using the HS714 5/16” x ¾” truss head bin bolts. (Truss head to the inside of ladder) 6. Starting at the top, continue to attach the vertical ladder to each GST-LD6403 using the GST-LD6404 retainer and HS717 Carriage bolt. Secure with HS722 serrated flange nut. 7. Splice each ladder section using the GST-LDR360 Splice plate Splice Plate GST-LDR360 Ladder Corner Bracket GST-LDR40 Ensure the truss head is to the inside of the ladder assembly.

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 22 Feed Bins Ladder Handrail Channel GST-LS6422 Ladder Handrail Gusset GST-LS6420 8. Attach the roof ladder to the corner brackets and roof stand-off brackets Using HS714 Truss head bin bolts and HS722 Serrated hex nuts. 9. Slide the Ladder handrail support channel through the first rung of the vertical ladder and the second rung of the roof ladder. 10. Attach the gusset, ladder handrail, and channel at the same time using the 605101 - 5/16” x 1 ¾” bolts provided. Corner Bracket GST-LDR40 Roof stand-off bracket GST-LS6405 (6’, 9’, & 12’ tanks) GST-LS6411 (7’ tank) Skip steps 9 and 10 and proceed to the next page if you are installing a Safety Cage system. Ladder Handrail GST-LS6421

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 23 Feed Bins Safety Cage 1. Attach the GST-LDR54SC ladder cage extension rails using the GST-LS6419, 2” spacer through the top two 3/8” diameter holes available on the vertical ladder. Secure using the FL0120331 5/16-18 x 2 ½ bolt and the HS722 Serrated Flange nut. GST-LS6404 Top View 3. Attach the GST-LS6416, 48” Tube to roof panel seem at the third hole from the ladder support bracket, using the HS712 bolt already installed 2. Attach the GST-LS6425 to the cage extension rail using the GST-LS6404 retainer and HS717 carriage bolt GST-LS6419 GST-LDR54SC GST-LS6425

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 24 Feed Bins 6. Attach the top safety cage ring GST-LS6413 (small Ring) flush to the top of the ladder extension rails. 7. Bolt the two loop halves together with the HS714 Truss Head bin bolt and HS722 Serrated Flange Nut. Tighten all bolts secure. Ensure the Truss Head of HS714 is to the inside of all cage loops GST-LS6417 GST-LS6404 4. Attach the GST-LS6417 to the roof ladder using two GST-LS6404 and one HS717 Carriage bolt. 5. Attach the GST-LS6416, 48” Tube to roof panel seem at the third hole from the ladder support bracket, using the HS712 bin bolt already installed. Slide the GST-LS6425 up or down the handrail to align tube with the top panel seam hole.

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 25 Feed Bins 8. Place the extension tubes to the inside of the loops and secure using the HS714 truss head tin bolt and the HS722 Serrated flange nut. 9. Continue working down the tank installing the loops and extension tubes. Only the bell extension uses the larger diameter cage loop. All others are the same size.

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 26 Feed Bins Pneumatic Fill Assembly Attach the GSTPNF1012 Latch to the GSTLD1022 bracket. Secure using the 605012 ¼” bolt and 60680 ¼” nylock nuts. Add additional Flange provided to inside of roof panel to ensure a tight seal (no sealant required on the inside of roof panel). Secure using HS712 bin bolt and HS722 serrated flange nut. Caulk each side of the holes on the Elbow Flange side of the roof panel. As shown in black Cut Exhaust extension tube to fit. Attach Clamp bands at center of roof panel using the HS712 Carriage bolt and HS722 serrated flange nut. Secure tube connections using the 60887 #10x3/4” self drilling screws provided. Side Fill Tube (not included in Kit). After installing lid assembly, apply the GST-PNF1011 edge grip seal around the top edge of peak ring. Attach the GST-LD1022 Latch bracket centered at the lid clamp bracket.

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 27 Feed Bins Pneumatic Fill Kits GST-PNF1026 Kit, Pneumatic Fill, 6' Tank 40° GST-PNF1027 Kit, Pneumatic Fill, 7' Tank 40° GST-PNF1029 Kit, Pneumatic Fill, 9' Tank 40° GST-PNF10212 Kit, Pneumatic Fill, 12' Tank 40° GST-PNF1020 Tube, 4" OD, 14 ga Galvanized, 20 foot section GST-PNF1030 Tube, 4" OD, 14 ga Galvanized, 10 foot section GST-PNF1034 Clamp Band Kit, 4" GST-PNF1036 Clamp Band Kit, 6" GST-PNF2000 Parts Kit, Pneumatic Fill, Universal, W/O Fill & Exhaust Tubes Roof Panel (inlet and outlet roof panels are the same) GST-RP640PF Roof Panel, Formed, 40 degree, 6ft Tank, Pneumatic fill GST-RP940PF Roof Panel, Formed, 40 degree, 9ft Tank, Pneumatic fill GST-RP740PF Roof Panel, Formed, 40 degree, 7ft Tank, Pneumatic fill GST-RP1240PF Roof Panel, Formed, 40 degree, 12ft Tank, Pneumatic fill Not provided with Kit Not provided with Kit GST-PNF1001 GST-PNF1008 6ft = GST-PNF1017 7ft = GST-PNF1022 9ft = GST-PNF1005 12ft = GST-PNF1023 GST-PNF1000 GST-PNF1016 GST-PNF1010 GST-PNF3001PF GST-PNF1003 GST-PNF1004

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 28 Feed Bins Erecting the Bin Before erecting your new bin, be sure all parts are assembled properly and hardware tightened securely. 1. Peel protective paper off decal before raising bin. 2. Cut 2” x 4” braces and fasten between legs as shown. 3. Raise the bin as shown below. Be sure to use appropriate equipment. • Be sure to use proper strength heavy equipment such as; crane, truck with hydraulic lift bed or other. • Level the legs, to assure stability, after the bin is raised. • Failure to adequately secure legs may result in damage to your Feed Bin. • Do not place bins in the immediate air flow from exhaust fans All bins shall have two Ground Connections. Ground Rod Clamps must be spaced equally around the bin. IMPORTANT! Make sure electrical equipment is properly installed and grounded by a qualified electrician according to the National Electrical Code. Bottom End View 2 x 4 brace

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 29 Feed Bins Ladder Matrix ROOF SIDEWALL SAFETY CAGE HAND RAIL GST-LDR36RA GST-LDR48RA GST-LDR72RA GST-LDR48A GST-LDR60A GST-LDR72A GST-LS6424 GST-LS6426 GST-LS6427 GST-LS6423 total feet /tank BFT-6'-1 1 1 1 1 0 1 1 9 BFT-6'-2 1 1 1 1 1 1 1 11 BFT-6'-3 1 1 2 1 1 1 1 14 BFT-6'-4 1 1 2 1 2 1 1 17 BFT-7'-1 1 1 1 1 1 1 1 11 BFT-7'-2 1 1 2 1 1 1 1 14 BFT-7'-3 1 1 2 1 2 1 1 17 BFT-7'-4 1 1 3 1 2 1 1 19 BFT-7'-5 1 1 3 1 3 1 0 22 BFT-7'-6 1 5 1 4 1 0 25 BFT-9'-1 1 1 1 1 1 1 1 11 BFT-9'-2 1 1 2 1 1 1 1 14 BFT-9'-3 1 1 2 1 2 1 1 17 BFT-9'-4 1 1 3 1 2 1 1 19 BFT-9'-5 1 1 3 1 3 1 0 22 BFT-9'-6 1 5 1 4 1 0 25 BFT-9'-7 1 1 1 3 1 5 1 0 27 BFT-12'-1 1 1 2 1 1 1 1 14 BFT-12'-2 1 1 2 1 2 1 1 17 BFT-12'-3 1 1 3 1 2 1 1 19 BFT-12'-4 1 1 3 1 3 1 0 22 BFT-12'-5 1 5 1 4 1 0 25 BFT-12'-6 1 1 3 1 5 1 0 27 BFT-12'-7 1 4 1 5 1 0 29

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 30 Feed Bins 6’ Diameter Components Corrugated sidewall sheets 1 Ring Bin GST-SWB620S (1) GST-SWB620S w/decal (1) 2 Ring Bin GST-SWB620 (2) GST-SWT620 (1) GST-SWT620 w/decal (1) 3 Ring Bin GST-SWB618 (2) GST-SWM620 (2) GST-SWT620 (1) GST-SWT620 w/decal (1) 4 Ring Bin GST-SWB618 (2) GST-SWM620 (2) GST-SWM620 (2) GST-SWT620 (1) GST-SWT620 w/decal (1) GST-RP640 Roof Panel GST-HB6 Hopper Brace GST-LG109 Leg 1-4 Ring GST-HP660 Hopper Panel (6) GST-PR22 Peak Ring GST-HC60 Hopper Collar GST-BP1 Base Plate, Top GST-BP2 Base Plate, Bottom

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 31 Feed Bins Item number Quantity Unit Item name GST-SWT620 1 EACH Side Wall Sheet, 20ga Top, 6 ft Tank GST-SWT6HS 1 EACH Sidewall, Top Sheet, w/Hog Slat Decal GST-SWM620 Varies EACH Side Wall Sheet, 20ga Middle, 6 ft Tank GST-SWB618 Varies EACH Side Wall Sheet, 18ga Bottom, 6 ft Tank GST-HP660 6 EACH Hopper Panel, Formed, 6 ft 60 Degree With Flange 18ga GST-RP640 6 EACH Roof Panel, Formed, 40 Degree, 6 ft Tank GST-LG109 4 EACH Leg, 12ga 6 ft 1-4 Rings GST-HB6 4 EACH Hopper Brace, 6 ft Tank, Formed GST-LS6408 1 EACH Ladder, Stand Off Support Brace, 6 ft Tank, Formed GST-LDR36RA 1 EACH Ladder, 36" Roof, 40 Degree GST-LDR60A 1 EACH Ladder, 60" Vertical GST-LDR72A 2 EACH Ladder, 72" Vertical GST-LD3001A 1 EACH Feed Bin, Lid Assembly, Polymer GST-PR22 1 EACH Peak Ring, Formed, 40 Degree, 22" Diameter GST-HC60 1 EACH Hopper Collar, Formed, 60 Degree, 6-9 ft Tank GST-HDW646016 1 EACH Hardware Package, 6 ft 4 ring, 60 Degree hopper, 16" collar HS712 Varies EACH Bolt 5/16-18 X 1 Hex Head Bin Gr 8.2 with PE Washer JS1000 HS714 Varies EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 HS716 4 EACH Bolt 3/8-16 X 1 Hex Head Gr 8 JS1000 HS719 Varies EACH Finish Hex Nut 5/16-18 Grade 5 JS1000 HS722 Varies EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 HS724 4 EACH Nut 3/8-16 Hex Serrated Flange Grade 5 JS1000 GST-BP1 4 EACH Leg Base Plate, Inside GST-BP2 4 EACH Leg Base Plate, Outside HS721 Varies ROLL Sealant Preformed Butyl Sealant 1/8" X 1/4" X 24' Rolls GST-LDR40 2 EACH Ladder, Corner Bracket, 40 Degree GST-LS6411 2 EACH Ladder, Stand Off Bracket, Roof 6 ft and 7 ft Tank, Formed GST-LS6406 1 EACH Ladder, Stand Off Bracket, Peak Right, Formed GST-LS6412 1 EACH Ladder, Stand Off Bracket, Peak Left, Formed GST-LS6403 Varies EACH Ladder, Stand Off Bracket GST-LS6404 Varies EACH Ladder, Stand Off Retainer GST-LDR360 Varies EACH Ladder, Splice Plate HS717 Varies EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 GST-LD1011 1 EACH Lid, Guide Bracket, Formed GST-LD1019 1 EACH Lid, Pull Guide Assembly GST-LS6423 1 EACH Ladder, Handrail Kit GST-LS6420 4 EACH Ladder, Handrail Bracket w/out Safety Cage, Formed GST-LS6421 2 EACH Ladder Handrail w/out Safety Cage GST-LS6422 2 EACH Ladder, Handrail Support Channel, Formed 605101 8 EACH Bolt Hex Cap 5/16-18 X 1-3/4'' Zinc HS722 8 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 32 Feed Bins 7’ Diameter Components Corrugated sidewall sheets 1 Ring Bin GST-SWB720S (1) GST-SWB720S w/decal (1) 2 Ring Bin GST-SWB718 (2) GST-SWT720 (1) GST-SWT720 w/decal (1) 3 Ring Bin GST-SWB718 (2) GST-SWM720 (2) GST-SWT720 (1) GST-SWT720 w/decal (1) 4 Ring Bin GST-SWB718 (2) GST-SWM718 (2) GST-SWM720 (2) GST-SWT720 (1) GST-SWT720 w/decal (1) 5 Ring Bin GST-SWB716 (2) GST-SWM718L (2) GST-SWM718 (2) GST-SWM720 (2) GST-SWT720 (1) GST-SWT720 w/decal (1) 6 Ring Bin GST-SWB714 (2) GST-SWM716L (2) GST-SWM718 (2) GST-SWM718 (2) GST-SWM720 (2) GST-SWT720 (1) GST-SWT720 w/decal (1) GST-PR22 Peak Ring GST-HP767 Hopper Panel GST-LB71 X-Brace Outer GST-LB72 X-Brace Inner GST-LG142 Leg 1-4 Ring GST-LG169 Leg 5-6 Ring GST-RP740 Roof Panel GST-HB7 Hopper Brace GST-HC60 Hopper Collar GST-BP1 Base Plate, Top GST-BP2 Base Plate, Bottom GST-HR767 Hopper Reinforcement Angle, 5-6 Ring

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 33 Feed Bins 7’ Diameter Components – continued Item number Quantity Unit Item name GST-SWT720 1 EACH Side Wall Sheet, 20ga Top, 7 ft Tank GST-SWT7HS 1 EACH Sidewall, Top Sheet, w/Hog Slat Decal GST-SWM716 varies EACH Side Wall Sheet, 16ga Middle, 7 ft Tank GST-SWM716L varies EACH Side Wall Sheet, 16ga Middle w/Leg Holes, 7 ft Tank GST-SWM718 varies EACH Side Wall Sheet, 18ga Middle, 7 ft Tank GST-SWM718L varies EACH Side Wall Sheet, 18ga Middle w/Leg Holes, 7 ft Tank GST-SWM720 varies EACH Side Wall Sheet, 20ga Middle, 7 ft Tank GST-SWB714 varies EACH Side Wall Sheet, 14ga Bottom, 7 ft Tank GST-SWB716 varies EACH Side Wall Sheet, 16ga Bottom, 7 ft Tank GST-SWB718 varies EACH Side Wall Sheet, 18ga Bottom, 7 ft Tank GST-SWB720S varies EACH Side Wall Sheet, 20ga Bottom/Top, 7 ft Tank GST-HP767 6 EACH Hopper Panel, Formed, 7 ft 67 Degree With Flange 16ga GST-RP740 6 EACH Roof Panel, Formed, 40 Degree, 7 ft Tank GST-LG142 4 EACH Leg, 12ga 7 ft 1-4 Rings, 9 ft 1-5 Rings GST-LG169 4 EACH Leg, 10ga 7 ft 5-6 Rings, 9 ft 6 Rings GST-HR767 (5-6 ring) 6 EACH Hopper Reinforcement, 7 ft Tank, 5-6 Ring, Formed GST-LB72 4 EACH Leg Brace, Outside, 7 ft Tank, Formed GST-LB71 4 EACH Leg Brace, Inside, 7 ft Tank, Formed GST-HB7 4 EACH Hopper Brace, 7 ft Tank, Formed GST-LS6409 2 EACH Ladder, Stand Off Support Brace, 7 ft Tank, Formed GST-LDR36RA 1 EACH Ladder, 36" Roof, 40 Degree GST-LDR84A 1 EACH Ladder, 84" Vertical GST-LDR72A 3 EACH Ladder, 72" Vertical GST-LD3001A 1 EACH Feed Bin, Lid Assembly, Polymer GST-PR22 1 EACH Peak Ring, Formed, 40 Degree, 22" Diameter GST-HC60 1 EACH Hopper Collar, Formed, 60 Degree, 6-9 ft Tank GST-HDW766716 1 EACH Hardware Package, 7 ft 6 ring, 67 Degree hopper, 16" collar HS712 varies EACH Bolt 5/16-18 X 1 Hex Head Bin Gr 8.2 with PE Washer JS1000 HS714 varies EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 HS716 17 EACH Bolt 3/8-16 X 1 Hex Head Gr 8 JS1000 HS719 varies EACH Finish Hex Nut 5/16-18 Grade 5 JS1000 HS722 varies EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 HS724 17 EACH Nut 3/8-16 Hex Serrated Flange Grade 5 JS1000 GST-BP1 4 EACH Leg Base Plate, Inside GST-BP2 4 EACH Leg Base Plate, Outside HS721 varies ROLL Sealant Preformed Butyl Sealant 1/8" X 1/4" X 24' Rolls GST-LDR40 2 EACH Ladder, Corner Bracket, 40 Degree GST-LS6411 2 EACH Ladder, Stand Off Bracket, Roof 6 ft and 7 ft Tank, Formed GST-LS6406 1 EACH Ladder, Stand Off Bracket, Peak Right, Formed GST-LS6412 1 EACH Ladder, Stand Off Bracket, Peak Left, Formed

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 34 Feed Bins GST-LS6403 varies EACH Ladder, Stand Off Bracket GST-LS6404 varies EACH Ladder, Stand Off Retainer GST-LDR360 varies EACH Ladder, Splice Plate HS717 varies EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 GST-LD1011 1 EACH Lid, Guide Bracket, Formed GST-LD1019 1 EACH Lid, Pull Guide Assembly GST-LS6424 1 EACH Ladder, Handrail Kit, Safety Cage GST-LS6419 4 EACH Bushing PVC .875 OD x 2.00 GST-LDR54SC 2 EACH Ladder, 54" Extension Rail, Safety Cage FL0120331 4 EACH Bolt Gr5 5/16-18 X 2 1/2 Zn HS722 34 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 GST-LS6416 9 EACH Safety Cage Vertical Support 48" GST-LS6417 2 EACH Safety Cage Vertical Support 24" GST-LS6404 6 EACH Ladder, Stand Off Retainer HS717 10 EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 HS712 6 EACH Bolt 5/16-18 X 1 Hex Head Bin Gr 8.2 with PE Washer JS1000 GST-LS6425 6 EACH Ladder, Safety Cage Support Mount Bracket, Formed GST-LS6413 4 EACH Safety Cage Loop, Formed HS714 14 EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 GST-LS6426 4 EACH Ladder, Cage Extension 4' GST-LS6416 7 EACH Safety Cage Vertical Support 48" HS722 16 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 GST-LS6413 2 EACH Safety Cage Loop, Formed HS714 14 EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 GST-LS6404 2 EACH Ladder, Stand Off Retainer HS717 2 EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 GST-LS6427 1 EACH Ladder, Cage Extension, 24" Bell GST-LS6417 7 EACH Safety Cage Vertical Support 24" HS722 16 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 GST-LS6414 2 EACH Safety Cage Loop, Bell, Formed HS714 14 EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 GST-LS6404 2 EACH Ladder, Stand Off Retainer HS717 2 EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 GST-LS6423 1 EACH Ladder, Handrail Kit GST-LS6420 4 EACH Ladder, Handrail Bracket w/out Safety Cage, Formed GST-LS6421 2 EACH Ladder Handrail w/out Safety Cage GST-LS6422 2 EACH Ladder, Handrail Support Channel, Formed 605101 8 EACH Bolt Hex Cap 5/16-18 X 1-3/4'' Zinc HS722 8 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 35 Feed Bins 9’ Diameter Components Corrugated sidewall sheets 1 Ring Bin GST-SWB920S (2) GST-SWB920S w/decal (1) 2 Ring Bin GST-SWB920 (3) GST-SWT920 (2) GST-SWT920 w/decal (1) 3 Ring Bin GST-SWB920 (3) GST-SWM920 (3) GST-SWT920 (2) GST-SWT920 w/decal (1) 4 Ring Bin GST-SWB918 (3) GST-SWM918 (3) GST-SWM920 (3) GST-SWT920 (2) GST-SWT920 w/decal (1) 5 Ring Bin GST-SWB916 (3) GST-SWM918 (3) GST-SWM918 (3) GST-SWM920 (3) GST-SWT920 (2) GST-SWT920 w/decal (1) 6 Ring Bin GST-SWB914 (3) GST-SWM916L (3) w/leg holes GST-SWM918 (3) GST-SWM918 (3) GST-SWM920 (3) GST-SWT920 (2) GST-SWT920 w/decal (1) 7 Ring Bin GST-SWB912 (3) GST-SWM912L (3) w/leg holes GST-SWM916 (3) GST-SWM916 (3) GST-SWM918 (3) GST-SWT920 (3) GST-SWT920 (2) GST-SWT920 w/decal (1) GST-BP1 Base Plate, Top GST-BP2 Base Plate, Bottom GST-LG142 Leg 1-5 Ring GST-LG169 Leg 6-7 Ring GST-HP960 Hopper Panel GST-RP940 Roof Panel GST-LB91 X-Brace Inner GST-LB92 X-Brace Outer GST-PR22 Peak Ring GST-HC60 Hopper Collar GST-HB9 Hopper Brace GST-LS6407 Ladder Support GST-HR960 Hopper Reinforcement angle (3-6 Ring)

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 36 Feed Bins 9’ Diameter Components - Continued Item number Quantity Unit Item name GST-SWT920 2 EACH Side Wall Sheet, 20ga Top, 9 ft Tank GST-SWT9HS 1 EACH Sidewall, Top Sheet, w/Hog Slat Decal GST-SWM920 Varies EACH Side Wall Sheet, 20ga Middle, 9 ft Tank GST-SWM918 Varies EACH Side Wall Sheet, 18ga Middle, 9 ft Tank GST-SWM918L Varies EACH Side Wall Sheet, 18ga Middle w/Leg Holes, 9 ft Tank GST-SWM916L Varies EACH Side Wall Sheet, 16ga Middle w/Leg Holes, 9 ft Tank GST-SWB920 Varies EACH Side Wall Sheet, 20ga Bottom, 9 ft Tank GST-SWB918 Varies EACH Side Wall Sheet, 18ga Bottom, 9 ft Tank GST-SWB916 Varies EACH Side Wall Sheet, 16ga Bottom, 9 ft Tank GST-SWB914 Varies EACH Side Wall Sheet, 14ga Bottom, 9 ft Tank GST-HP960 9 EACH Hopper Panel, Formed, 9 ft 60 Degree With Flange 16ga GST-RP940 9 EACH Roof Panel, Formed, 40 Degree, 9 ft Tank GST-LG142 6 EACH Leg, 12ga 7 ft 1-4 Rings, 9 ft 1-5 Rings GST-LG169 6 EACH Leg, 10ga 7 ft 5-6 Rings, 9 ft 6 Rings GST-HR960 (3-6 Ring) 9 EACH Hopper Reinforcement, 9 ft Tank, 3-6 Ring, Formed GST-LB92 6 EACH Leg Brace, Outside, 9 ft Tank, Formed GST-LB91 6 EACH Leg Brace, Inside, 9 ft Tank, Formed GST-HB9 6 EACH Hopper Brace, 9 ft Tank, Formed GST-LS6407 2 EACH Ladder, Stand Off Support Brace, 9 ft Tank, Formed GST-LDR48RA 1 EACH Ladder, 48" Roof, 40 Degree GST-LDR940 2 EACH Ladder, Roof Support angle, 9 ft , Formed GST-LDR84A 1 EACH Ladder, 84" Vertical GST-LDR72A 3 EACH Ladder, 72" Vertical GST-LD3001A 1 EACH Feed Bin, Lid Assembly, Polymer GST-PR22 1 EACH Peak Ring, Formed, 40 Degree, 22" Diameter GST-HC60 1 EACH Hopper Collar, Formed, 60 Degree, 6-9 ft Tank GST-HDW966016 1 EACH Hardware Package, 9 ft 6 ring, 60 Degree hopper, 16" collar HS712 Varies EACH Bolt 5/16-18 X 1 Hex Head Bin Gr 8.2 with PE Washer JS1000 HS714 Varies EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 HS716 24 EACH Bolt 3/8-16 X 1 Hex Head Gr 8 JS1000 HS718 6 EACH Washer 3/8 X 2 X 1/8 Curved Fender Zinc Finish HS719 Varies EACH Finish Hex Nut 5/16-18 Grade 5 JS1000 HS722 Varies EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 HS724 24 EACH Nut 3/8-16 Hex Serrated Flange Grade 5 JS1000 GST-BP1 6 EACH Leg Base Plate, Inside GST-BP2 6 EACH Leg Base Plate, Outside HS721 Varies ROLL Sealant Preformed Butyl Sealant 1/8" X 1/4" X 24' Rolls GST-LDR40 2 EACH Ladder, Corner Bracket, 40 Degree GST-LS6405 2 EACH Ladder, Stand Off Bracket, Roof 9 ft and 12 ft Tank, Formed GST-LS6406 1 EACH Ladder, Stand Off Bracket, Peak Right, Formed GST-LS6412 1 EACH Ladder, Stand Off Bracket, Peak Left, Formed GST-LS6403 Varies EACH Ladder, Stand Off Bracket GST-LS6404 Varies EACH Ladder, Stand Off Retainer GST-LDR360 Varies EACH Ladder, Splice Plate HS717 Varies EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 GST-LD1011 1 EACH Lid, Guide Bracket, Formed GST-LD1019 1 EACH Lid, Pull Guide Assembly GST-LS6424 1 EACH Ladder, Handrail Kit, Safety Cage GST-LS6419 4 EACH Bushing PVC .875 OD x 2.00 GST-LDR54SC 2 EACH Ladder, 54" Extension Rail, Safety Cage

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 37 Feed Bins FL0120331 4 EACH Bolt Gr5 5/16-18 X 2 1/2 Zn HS722 34 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 GST-LS6416 9 EACH Safety Cage Vertical Support 48" GST-LS6417 2 EACH Safety Cage Vertical Support 24" GST-LS6404 6 EACH Ladder, Stand Off Retainer HS717 10 EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 HS712 6 EACH Bolt 5/16-18 X 1 Hex Head Bin Gr 8.2 with PE Washer JS1000 GST-LS6425 6 EACH Ladder, Safety Cage Support Mount Bracket, Formed GST-LS6413 4 EACH Safety Cage Loop, Formed HS714 14 EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 GST-LS6426 4 EACH Ladder, Cage Extension 4' GST-LS6416 7 EACH Safety Cage Vertical Support 48" HS722 16 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 GST-LS6413 2 EACH Safety Cage Loop, Formed HS714 14 EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 GST-LS6404 2 EACH Ladder, Stand Off Retainer HS717 2 EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 GST-LS6427 1 EACH Ladder, Cage Extension, 24" Bell GST-LS6417 7 EACH Safety Cage Vertical Support 24" HS722 16 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 GST-LS6414 2 EACH Safety Cage Loop, Bell, Formed HS714 14 EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 GST-LS6404 2 EACH Ladder, Stand Off Retainer HS717 2 EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 GST-LS6423 1 EACH Ladder, Handrail Kit GST-LS6420 4 EACH Ladder, Handrail Bracket w/out Safety Cage, Formed GST-LS6421 2 EACH Ladder Handrail w/out Safety Cage GST-LS6422 2 EACH Ladder, Handrail Support Channel, Formed 605101 8 EACH Bolt Hex Cap 5/16-18 X 1-3/4'' Zinc HS722 8 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 38 Feed Bins 12’ Diameter Components Corrugated sidewall sheets 1 Ring Bin GST-SWB1218S (3) GST-SWB1218S w/decal (1) 2 Ring Bin GST-SWB1214 (4) GST-SWT1220 (3) GST-SWT1220 w/decal (1) 3 Ring Bin GST-SWB1214 (4) GST-SWM1218 (4) GST-SWT1220 (3) GST-SWT1220 w/decal (1) 4 Ring Bin GST-SWB1214 (4) GST-SWM1216 (4) GST-SWM1220 (4) GST-SWT1220 (3) GST-SWT1220 w/decal (1) 5 Ring Bin GST-SWB1212 (4) GST-SWM1216 (4) GST-SWM1218 (4) GST-SWM1220 (4) GST-SWT1220 (3) GST-SWT1220 w/decal (1) 6 Ring Bin GST-SWB1212 (4) GST-SWM1214L (4) w/leg holes GST-SWM1216 (4) GST-SWM1218 (4) GST-SWM1220 (4) GST-SWT1220 (3) GST-SWT1220 w/decal (1) 7 Ring Bin GST-SWB1212 (4) GST-SWM1212L (4) w/leg holes GST-SWM1214 (4) GST-SWM1216 (4) GST-SWM1218 (4) GST-SWM1220 (4) GST-SWT1220 (3) GST-SWT1220 w/decal (1) GST-PR22 Peak Ring GST-LG173 Leg 12’ 1-5 Rings GST-LG200 Leg 12’ 6-7 Rings GST-LB121 X-Brace Inner GST-LB122 X-Brace Outer GST-BP1 Base Plate, Top GST-BP2 Base Plate, Bottom GST-HP1260 Hopper Panel GST-HC6012G Hopper Collar GST-RP1240 Roof Panel GST-HB12 Hopper Brace GST-LS6410 Ladder Support

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 39 Feed Bins 12’ Diameter Components - Continued Item number Quantity Unit Item name GST-SWT1220 3 EACH Side Wall Sheet, 20ga Top, 12 ft Tank GST-SWT12HS 1 EACH Sidewall, Top Sheet, w/Hog Slat Decal GST-SWM1220 Varies EACH Side Wall Sheet, 20ga Middle, 12 ft Tank GST-SWM1218 Varies EACH Side Wall Sheet, 18ga Middle, 12 ft Tank GST-SWM1216 Varies EACH Side Wall Sheet, 16ga Middle, 12 ft Tank GST-SWM1214L Varies EACH Side Wall Sheet, 14ga Middle w/Leg Holes, 12 ft Tank GST-SWB1212 Varies EACH Side Wall Sheet, 12ga Bottom, 12 ft Tank GST-SWB1214 Varies EACH Side Wall Sheet, 14ga Bottom, 12 ft Tank GST-SWB1218S Varies EACH Side Wall Sheet, 18ga Bottom/Top, 12 ft Tank GST-HP1260 12 EACH Hopper Panel, Formed, 12 ft 60 Degree With Flange 14ga GST-RP1240 12 EACH Roof Panel, Formed, 40 Degree, 12 ft Tank GST-LG173 8 EACH Leg, 12ga 12 ft 1-5 Rings GST-LG200 8 EACH Leg, 10ga 12 ft 6-7 Rings GST-HR1260 (Optional) 12 EACH Hopper Reinforcement, 12 ft Tank, Formed GST-LB122 16 EACH Leg Brace, Outside, 12 ft Tank, Formed GST-LB121 16 EACH Leg Brace, Inside, 12 ft Tank, Formed GST-HB12 8 EACH Hopper Brace, 12 ft Tank, Formed GST-LS6410 2 EACH Ladder, Stand Off Support Brace, 12 ft Tank, Formed GST-LDR72RA 1 EACH Ladder, 72" Roof, 40 Degree GST-LDR1240 2 EACH Ladder, Roof Support angle, 12 ft, Formed GST-LDR84A 3 EACH Ladder, 84" Vertical GST-LDR72A 1 EACH Ladder, 72" Vertical GST-LDR1240 2 EACH Ladder, Roof Support angle, 12 ft, Formed GST-LD3001A 1 EACH Feed Bin, Lid Assembly, Polymer GST-PR22 1 EACH Peak Ring, Formed, 40 Degree, 22" Diameter GST-HC6012G 1 EACH Hopper Collar, 60 Degree, Galvanized, 12ft Tank GST-HDW1266016 1 EACH Hardware Package, 12 ft 6 ring, 60 Degree hopper, 16" collar HS712 1 EACH Bolt 5/16-18 X 1 Hex Head Bin Gr 8.2 with PE Washer JS1000 HS714 Varies EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 HS716 56 EACH Bolt 3/8-16 X 1 Hex Head Gr 8 JS1000 HS718 8 EACH Washer 3/8 X 2 X 1/8 Curved Fender Zinc Finish HS719 1 EACH Finish Hex Nut 5/16-18 Grade 5 JS1000 HS722 Varies EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 HS724 56 EACH Nut 3/8-16 Hex Serrated Flange Grade 5 JS1000 GST-BP1 8 EACH Leg Base Plate, Inside GST-BP2 8 EACH Leg Base Plate, Outside HS721 Varies ROLL Sealant Preformed Butyl Sealant 1/8" X 1/4" X 24' Rolls GST-LDR40 2 EACH Ladder, Corner Bracket, 40 Degree GST-LS6405 2 EACH Ladder, Stand Off Bracket, Roof 9 ft and 12 ft Tank, Formed GST-LS6406 1 EACH Ladder, Stand Off Bracket, Peak Right, Formed GST-LS6412 1 EACH Ladder, Stand Off Bracket, Peak Left, Formed GST-LS6403 Varies EACH Ladder, Stand Off Bracket GST-LS6404 Varies EACH Ladder, Stand Off Retainer GST-LDR360 Varies EACH Ladder, Splice Plate HS717 Varies EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 GST-LD1011 1 EACH Lid, Chain Guide Bracket, Formed GST-LD1019 1 EACH Chain Pull Guide Assembly GST-LS6424 1 EACH Ladder, Handrail Kit, Safety Cage GST-LS6419 4 EACH Bushing PVC .875 OD x 2.00

Hog Slat Inc. Newton Grove, NC USA Sept. 2021 40 Feed Bins GST-LDR54SC 2 EACH Ladder, 54" Extension Rail, Safety Cage FL0120331 4 EACH Bolt Gr5 5/16-18 X 2 1/2 Zn HS722 34 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 GST-LS6416 9 EACH Safety Cage Vertical Support 48" GST-LS6417 2 EACH Safety Cage Vertical Support 24" GST-LS6404 6 EACH Ladder, Stand Off Retainer HS717 10 EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 HS712 6 EACH Bolt 5/16-18 X 1 Hex Head Bin Gr 8.2 with PE Washer JS1000 GST-LS6425 6 EACH Ladder, Safety Cage Support Mount Bracket, Formed GST-LS6413 4 EACH Safety Cage Loop, Formed HS714 14 EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 GST-LS6426 4 EACH Ladder, Cage Extension 4' GST-LS6416 7 EACH Safety Cage Vertical Support 48" HS722 16 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 GST-LS6413 2 EACH Safety Cage Loop, Formed HS714 14 EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 GST-LS6404 2 EACH Ladder, Stand Off Retainer HS717 2 EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 GST-LS6427 1 EACH Ladder, Cage Extension, 24" Bell GST-LS6417 7 EACH Safety Cage Vertical Support 24" HS722 16 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000 GST-LS6414 2 EACH Safety Cage Loop, Bell, Formed HS714 14 EACH Bolt 5/16-18 X 3/4 Truss Head Bin Gr 8.2 W/PE Washer JS1000 GST-LS6404 2 EACH Ladder, Stand Off Retainer HS717 2 EACH Bolt 5/16-18 X 1 Carriage Gr 5.2 JS1000 GST-LS6423 1 EACH Ladder, Handrail Kit GST-LS6420 4 EACH Ladder, Handrail Bracket w/out Safety Cage, Formed GST-LS6421 2 EACH Ladder Handrail w/out Safety Cage GST-LS6422 2 EACH Ladder, Handrail Support Channel, Formed 605101 8 EACH Bolt Hex Cap 5/16-18 X 1-3/4'' Zinc HS722 8 EACH Nut 5/16-18 Hex Serrated Flange Grade 5 JS1000

RkJQdWJsaXNoZXIy MTA3MzU=