Hog Slat Inc. Newton Grove, NC USA June 2026 1 Feed Systems FEED SYSTEM ASSEMBLY & OPERATING INSTRUCTIONS
Hog Slat Inc. Newton Grove, NC USA June 2026 2 Feed Systems Table of Contents SAFETY INFORMATION ...................................................................................................................................3 GENERAL SAFETY NOTES ................................................................................................................................4 GENERAL ASSEMBLY / OPERATION NOTES ......................................................................................................5 GENERAL INSTALLATION NOTES: ....................................................................................................................5 GROW-CHAIN™ FEED SYSTEM PRINCIPLE OF OPERATION ................................................................................5 GROW-CHAIN™ PLANNING .............................................................................................................................6 SYSTEM LAYOUT:................................................................................................................................................... 6 WINCHING GUIDELINES:......................................................................................................................................... 7 GROW-CHAIN™ WEIGHT, LOAD AND LENGTH ............................................................................................................ 7 DRIVE UNIT REQUIREMENTS AND CHAIN STRETCH ......................................................................................................... 8 GEARBOX SPECIFICATIONS ...................................................................................................................................... 8 FEED DELIVERY RATES ............................................................................................................................................ 8 INSTALLATION INSTRUCTIONS .......................................................................................................................9 COMPONENT LAYOUTS / PARTS LIST.............................................................................................................18 DRIVE UNIT WITH GEAR HEAD (HSFC11-60 / HSFC11-90 / HSFC11-120) ............................................................. 18 MOTOR ANTI-ROOST COVER (HSFC11-30)........................................................................................................ 20 HOPPER 1 LINE FILL (HSFC19).......................................................................................................................... 21 HOPPER 2 LINE FILL (HSFC30).......................................................................................................................... 22 120 LB EXTENSION HOPPER (HSFC20) ............................................................................................................. 23 90° CORNER (HSFC2E) .................................................................................................................................... 24 DUAL TRACK FEED SYSTEM.............................................................................................................................. 25 DUAL TRACK CHAIN CORNER (HSFCM10L / HSFCM10R) ................................................................................... 26 FLAT CHAIN SYSTEM COMPONENTS ................................................................................................................ 27 HSFCG-XX ...................................................................................................................................................... 31 TROUBLESHOOTING GUIDE .......................................................................................................................... 32 HOG SLAT LIMITED WARRANTY .....................................................................................................................33
Hog Slat Inc. Newton Grove, NC USA June 2026 3 Feed Systems Safety Information Read all safety messages in this manual and on equipment safety decals. Follow recommended precautions and safe operating practices. Always keep safety decals in good condition and replace missing or damaged decals. Safety Decals and Warning Labels Caution, Warning, and Danger decals have been placed on the equipment to warn of potentially dangerous situations. Care should be taken to keep this information intact and easy to read at all times. Replace missing or damaged safety signs. Safety – Alert Symbol: When you see this symbol on your equipment, be alert to the potential or personal injury. GrowerSelect equipment is designed to be installed and operated as safely as possible, however, hazards do exist. Signal Words Signal words are used in conjunction with the safety-alert symbol to identify the severity of the warning. DANGER - identifies immediate hazards which WILL result in severe personal injury or death. WARNING - identifies hazards or unsafe practices which COULD result in severe personal injury and death. CAUTION – identifies hazards or unsafe practices which COULD result in minor personal injury or product or property damage. WARNING – MOVING PARTS • Keep hands and clothing clear of moving parts. Chain Disk can cut and crush. • Severe personal injury will result if the electrical power is not disconnected prior to servicing the unit. Disconnect electrical power before inspecting or servicing equipment unless maintenance instructions specifically state otherwise. Ground all electrical equipment for safety. All electrical wiring must be done by a qualified electrician in accordance with local and national electrical codes. Ground all non-current carrying metal parts to guard against electrical shock. With the exception of motor overload protection, electrical disconnects and over current protection are not supplied with the equipment. Screw torque tightening requirement for enclosure box is 15 in-lbs and terminal strip is 7 in-lbs. DANGER – ELECTROCUTION HAZARD
Hog Slat Inc. Newton Grove, NC USA June 2026 4 Feed Systems General Safety Notes The assembly, installation, and maintenance must be performed by qualified personnel. • Safety notes and warnings in these instructions and on the system equipment must be followed. Failure to follow specified instructions may cause damage to equipment and/or personal injury or death. • All components in the GROW-CHAIN™ system must be transported and assembled properly. • System may only be operated if all the necessary emergency and alarm systems are connected and operational. • System must be maintained at regular intervals. • Only manufacturer-approved components and accessories may be operated in conjunction with the system. • A lockable main switch must be installed between the controls and the main power capable of shutting the system down. It must be ensured that the system cannot be turned on by a third party. • Before components in the feed system are opened, the chain must have come to a complete stop. • Work on the feed system may only be carried out with the corresponding safety equipment (work gloves etc.). • All system parts must be properly grounded to guard against electrical shock. • The system may only be operated if all components are closed (driving unit, deflector corner pieces, and feed receiving station). • The system must be switched off immediately if the conveyor chain is blocked. • In systems with two or more feed bins in a row, only one bin may dispense feed into the feed system. • The system can be started automatically using the controls. It must be ensured that no person can reach into dangerous places with their hands. • The safety equipment may not be switched to inactive. • The feed system may only be repaired by people who are authorized by the manufacturer. • These instructions are to be submitted to the system operator following successful assembly. • Always wear protective clothing and any applicable Personal Protective Equipment (Safety Glasses and/or Ear Plugs) when working with the equipment. • Discarded materials, equipment, and boxes should be recycled in accordance with local and national codes. Note: System is to be wired in accordance with all applicable local and national electrical wiring codes. All wiring sizes and fuse capacities are to be sized according to applicable electrical code specifications or other regulations.
Hog Slat Inc. Newton Grove, NC USA June 2026 5 Feed Systems General Assembly / Operation Notes Prior to performing any work on Grow-Chain Feed System, read this entire manual. These assembly/operating instructions manual is intended to provide guidelines for the installation of system. Instructions should be considered as recommendations only. Actual installation may vary depending on specific conditions. Wiring diagrams are included within this manual. Instructions should only be carried out by a qualified technician. This person must have a good understanding of technical issues and drawings in both mechanical and electrical areas. The system is only suitable for operation in dry areas. System parts that are assembled outside the house must be adequately protected against moisture. Do not pressure wash the drive unit, chain fill hopper, unsealed corners, switch, controller or any other electronic components. The surfaces on which the system parts are assembled must be able to withstand the static loads. The GROW-CHAIN™ Feed System must not exceed any of the design criteria (See Grow-Chain Feed System Specifications). Refer to GROW-FLEX™ AUGER SYSTEM Manual (Hog Slat part # HSMANUAL-020) for proper installation of the GROW-FLEX™ AUGER SYSTEM. Only dry feed may be transported in the feed conveyor system (maximum residual moisture = 14%, maximum filling level = 50%). The feed can be floury, crumbly, or in pellets. GENERAL INSTALLATION NOTES: Make sure that power is disconnected from system prior to servicing. Installation of this equipment and related OEM equipment should be in accordance with these instructions, OEM’s installation instructions and local codes (if applicable). Failure to follow specified instructions may cause damage to equipment and/or personal injury or death. Take special note of any Warnings or Safety Decals on the equipment and in manuals. Always wear protective clothing and any applicable Personal Protective Equipment (Safety Glasses and/or Ear Plugs) when working with the equipment. Discarded materials, equipment and boxes should be recycled in accordance with local and national codes. GROW-CHAIN™ Feed System Principle of Operation The structure of the GROW-CHAIN™ Feed System depends on the conditions at the site and must be designed individually. The length of the conveyer trough are calculated by the seller. The manufacturer must be consulted before any extension of the feed conveyer system with corner pieces and / or conveyer troughs. The GROW-CHAIN™ Feed system is a closed loop made up of trough, flat chain and corners. The flat chain lays in the bottom of the trough and coveys feed thoughout the building. The feed is distributed into the building by a GROW-FLEX™ AUGER SYSTEM to the chain fill hopper.
Hog Slat Inc. Newton Grove, NC USA June 2026 6 Feed Systems GROW-CHAIN™ Planning System Layout: Single Loop Configuration Figure 8 Configuration NOTE: In the case of two drive units on a single loop, ensure the drive units are properly positioned. The Y distance and X distance must be equal.
Hog Slat Inc. Newton Grove, NC USA June 2026 7 Feed Systems Winching Guidelines: Winches Breeder Application Recommendations: Use (1) 5k lb. winch at 2:1 ration for each trough side up to 600 ft. systems. Layer Application Recommendations: Use (1) 5k lb. winch at 1:1 ration for each trough side up to 300 ft. systems. Use (2) 5k lb. winch at 1:1 ration for each trough side up to 600 ft. systems. Support Chain required when perch pipe is used. Weight of system to rest on support chains, not the winching cable. Cable Recommend using 3/16” stainless steel or galvanized cable up to 500 ft systems. Cable drops and hangers must be placed at every trough coupler. Cup Hooks Recommend using HSH049 - Screw Hook 3/8" (.375") X 4" Zinc Plated Maximum hook spacing of 10’ for drops when hanging single trough Maximum hook spacing of 5’ for drops when hanging Dual Track systems GROW-CHAIN™ Weight, Load and Length To calculate the total weight of the system, add the weights of the components. Below are the approximate weights of the components: Weight of Components (w/o Feed) Part # Description Lbs Kgs HSFC19 Hopper 1 Line Fill Only (w/o Feed) 60 27 HSFC30 Hopper 2 Line Fill Only (w/o Feed) 71 32 HSFC20 Hopper Extension 1 Line (w/o Feed) 34 15 HSFC11-60 Drive Unit Single Line 60FPM (w/o Motor) 59 27 HSFC11-90 Drive Unit Single Line 90FPM (w/o Motor) 59 27 HS9036 Motor 2 HP 1 Ph 1750 RPM 60Hz 230v 48 22 HSFC2E Corner 90° w/PET Bushing 11 5 HSFCM-10R Male Corner- Right 103 47 HSFCM-10L Male Corner- Left 103 47 Weight of Trough per Ft (with Feed) * Weights include the trough, feed, flat chain, grill and coupler Part# Description Lbs* Kgs* HS618-8 Trough 8' Medium Wide for Hen 18GA 8.6 3.9 HS618-10 Trough 10' Medium Wide for Hen 18GA 8.6 3.9 HS618-12 Trough 12' Medium Wide for Hen 18GA 8.6 3.9
Hog Slat Inc. Newton Grove, NC USA June 2026 8 Feed Systems Drive Unit Requirements and Chain Stretch Total Chain Length Per Loop Chain Stretch Drive Unit Config Motor HP 60FPM Motor HP 90FPM Links to be Removed Equivalent Stretch in Inches Must Be the Same Must Be the Same Ft 1 Drive 2 Drive 1 Drive 2 Drive 1 Drive 2 Drive 1 Drive 2 Drive 0-300 7 2 12 3 1 only 1.0 X 2.0 X 300-400 10 3 17 5 1 only 1.0 X 2.0 X 400-500 13 3 21 5 1 only 1.0 X 2.0 X 500-600 15 4 25 7 1 only 1.0 X 2.0 X 600-700 18 5 29 8 1 or 2 1.0 1.0 2.0 2.0 700-800 21 5 35 8 1 or 2 1.0 1.0 2.0 2.0 800-900 23 6 38 10 1 or 2 2.0 1.0 2.0 2.0 900-1000 X 7 X 12 2 only X 2.0 X 2.0 1000-1100 X 7 X 12 2 only X 2.0 X 2.0 1100-1200 X 8 X 13 2 only X 2.0 X 2.0 1200-1300 X 9 X 15 2 only X 2.0 X 2.0 Loops Longer than 1300 ft. Not Recommended Bold Indicates Recommended Configuration Gearbox Specifications Direct Drive Gearbox and Motor 60Hz 60 FPM 90 FPM 1725 RPM Input 51:1 35:1 Motor Shaft Diameter 5/8" 5/8" Gearbox Output Shaft Diameter 1-1/8" 1-1/8" Feed Delivery Rates (LBS/MIN) 60 FPM 90 FPM Mini Hopper Min/Max 35/54 52/75
Hog Slat Inc. Newton Grove, NC USA June 2026 9 Feed Systems Installation Instructions STEP #1 Layout components in the desired configuration on the ground. Use the System Layout section as a guide. NOTE: When the standard length of trough needs to be shortened, squarely cut the trough to the dimensions below. DIMENSION REF. DESCRIPTION A 2-5/8” (6.67 cm) B 2-1/2” (6.35 cm)
Hog Slat Inc. Newton Grove, NC USA June 2026 10 Feed Systems STEP #2 Connect the trough to hopper.
Hog Slat Inc. Newton Grove, NC USA June 2026 11 Feed Systems STEP #3 Connect the trough to drive units.
Hog Slat Inc. Newton Grove, NC USA June 2026 12 Feed Systems STEP #4 Connect all troughs with couplers.
Hog Slat Inc. Newton Grove, NC USA June 2026 13 Feed Systems STEP #5 Connect corners to trough.
Hog Slat Inc. Newton Grove, NC USA June 2026 14 Feed Systems STEP #6 Suspend system and check for loose hardware in trough. Reference Winching Guidelines on page 7. STEP #7 Install cleanout cover on trough.
Hog Slat Inc. Newton Grove, NC USA June 2026 15 Feed Systems STEP #8 Install chain in the desired direction. Properly tense the chain and connect sections of chain using chain breaking tool. Once the chain has been routed around the feed system, attach a 2 ton rated cable puller to the chain as illustrated in the photo. 1) With the shear pin removed, thighten the chain until the chain is slightly streahed and equally taut throughout the feed system. 2) Slowly release the tension on the chain allowing the chain to rest in a pre-steached position. Some level of recoil should be observed. 3) Based on the total chain loop length, remove the number of chain links as indicated in the chart below. 4) Once the links are removed, tighted the chain and connect the ends with the chain breaking tool. 5) Remove the cable puller and re-install the shear pin. 6) To confirm the chain is properly installed, check the chain tension mid-point between the hopper and corner. After several days of operation, the chain tension may need to be adjusted by removing chain links.
Hog Slat Inc. Newton Grove, NC USA June 2026 16 Feed Systems CONNECTING THE CHAIN Position the chain in the With a hammer, strike the chain chain breaking tool link in this location to connect the links BREAKING THE CHAIN Position the chain in the With a hammer, strike the chain chain break tool as shown link in this location to separate the links
Hog Slat Inc. Newton Grove, NC USA June 2026 17 Feed Systems STEP #9 Install and wire drive unit motors and controls. WIRING DIAGRAM FOR DRIVE UNIT 2 HP MOTOR ON ONE CONTROLLER STEP #10 With system suspended, inspect system for levelness and perform run-in procedure.
Hog Slat Inc. Newton Grove, NC USA June 2026 18 Feed Systems COMPONENT LAYOUTS / PARTS LIST DRIVE UNIT WITH GEAR HEAD (HSFC11-60 / HSFC11-90 / HSFC11-120)
Hog Slat Inc. Newton Grove, NC USA June 2026 19 Feed Systems PARTS LIST ITEM QTY PART NUMBER DESCRIPTION 1 1 HSFC11-28 HOUSING, MAIN-FC DRIVE 2 1 HSFC11-33 YOKE SHEAR PLATE, FC DRIVE 3 1 HSFC11-C POWER SHOE ASY-FC DRIVE 4 1 HSFC11-11 GEAR DRIVE, DRIVE UNIT FLAT CHAIN SYSTEM 5 1 HSFC11-B STRIPPER ASSY, CHAIN - FC DRIVE 6 1 HSFC11-18 DRIVE UNIT, DRIVE SPROKET, COLLAR 7 4 6E10007 BOLT, CAP SCREW 5/16-18 X 1" GR5 FLANGE ZINC 8 4 60624 NUT, HEX SERRATED FLANGE 5/16-18 GRADE 2 YELLOW ZINC 9 1 HSFC11-15 SHEAR PIN, .2"x1.25" MEDIUM STRENGTH 10 2 26036 SCREW, SET 5/16-18 X 1/2 BLACK OXIDE CUP POINT 11 1 5WE57 KEY, MACHINES 1/4" X 1 1/4" UNDERSIZED SQUARE END 12 2 60514 BOLT, HEX 3/8-16 X 3/4" 13 4 60598 WASHER, LOCK 3/8" ZINC 14 2 60572 HEX, NUT 3/8-16 15 6 60853 WASHER, FLAT USS 3/8 X 1" Zn 16 2 60516 Bolt, Hex Cap, 3/8"-16 X 1 1/4" Gr. 5 Zinc 17 2 HSFC11-1 GUIDE, FC DRIVE 18.A 18.B 18.C 1 HSGRFC001 HSGRFC002 HSGRFC003 GEAR HEAD FLAT CHAIN-60 FPM (HSFC11-60) GEAR HEAD FLAT CHAIN-90 FPM (HSFC11-90) GEAR HEAD FLAT CHAIN-120 FPM (HSFC11-120) 19 1 HSFC11-39 COVER, FRONT - FC DRIVE 20 1 HS1155-10 KNOB, THREE ARM 1/4"-20 X 1" LONG STEEL STUD 21 1 8694K67 (cover) NEOPRENE GASKET TAPE- 1/8" X 3/4" SELF ADHESIVE 22 4 60570 NUT, HEX, 1/4-20 ZINC 23 4 60596 WASHER, LOCK 1/4'' ZINC 24 4 21157 1/4" - 20 X 1-1/4” CARRIAGE BOLT ZINC
Hog Slat Inc. Newton Grove, NC USA June 2026 20 Feed Systems MOTOR ANTI-ROOST COVER (HSFC11-30) PARTS LIST (HSFC11-30) ITEM QTY PART NUMBER DESCRIPTION 1 1 HSFC11-25 COVER, MTR-FC DRIVE 2 1 HSFC11-23 COVER, ANTI-ROOST, SHORT-FC DRIVE 3 4 65037 PIN, COTTER 3/32” X 1-1/4” ZINC 4 2 HSFC11-22 COVER, MOTOR PLATE – FC DRIVE 5 1 HSFC11-24 COVER, ANTI-ROOST LONG – FC DRIVE 6 10 6E10002 RIVET, BLIND 3/16 X .300 STEEL, ZINC
Hog Slat Inc. Newton Grove, NC USA June 2026 21 Feed Systems HOPPER 1 LINE FILL (HSFC19) PARTS LIST (HSFC19) ITEM QTY PART NUMBER DESCRIPTION 1 1 HSFC19-4 FLAT CHAIN, MINI HOPPER, IDLER GEAR AXLE 2 1 HSFC19-5 FLAT CHAIN, 1 LINE HOPPER, OUTPUT FEED LEVEL SET 3 1 HSFC19-17 FLAT CHAIN, MINI HOPPER, IDLER GEAR STRIPPER 4 1 HSFC11-35 GUIDE, FC DRIVE 5 8 60572 HEX, NUT 3/8-16 6 1 HSFC19-23 FLAT CHAIN, MINI HOPPER, BACK COVER 7 1 HSFC19-32 1 LINE, FLAT CHAIN, HOPPER WELDMENT 8 1 HSFC19-31 HOPPER, IDLER WELDMENT MINI - FC 9 6 60579 Washer Flat 1/4" SS 10 2 0148017 Type D - Wing Screw - Cup Point 1/4"-20x1 Zinc 11 4 60686 Hex Bolt - 1/4-20 X 1 SS 12 4 21157 BOLT, CARRIAGE 1/4-20 X 1 1/4 Zn 13 4 60570 NUT, HEX, 1/4-20 ZINC 14 8 60596 WASHER, LOCK 1/4'' ZINC 15 19 0125677 1/4-20 .027 - .165 RIBBED BODY LOW PROFILE NUTSERT STEEL - YELLOW ZINC 16 1 65039 3/32" x 1-3/4" ZINC FINISH EXTENDED PRONG COTTER PIN 17 4 52088 Bolt, Eye, 3/8"-16 X 2 1/2" Length-2 1/4" Thread Length Zinc 18 8 60853 WASHER, FLAT USS 3/8 X 1" Zn 19 4 60598 WASHER, LOCK 3/8" ZINC (FOR EYEBOLTS)
Hog Slat Inc. Newton Grove, NC USA June 2026 22 Feed Systems HOPPER 2 LINE FILL (HSFC30) PARTS LIST (HSFC30) ITEM QTY PART NUMBER DESCRIPTION 1 1 HSFC30-01 DUAL LINE, FLAT CHAIN, HOPPER WELDMENT 2 1 HSFC19-23 FLAT CHAIN, MINI HOPPER, BACK COVER 3 6 60579 Washer Flat 1/4" SS 4 4 60686 Hex Bolt - 1/4-20 X 1 SS 5 2 HSFC19-31 HOPPER, IDLER WELDMENT MINI - FC 6 1 HSFC30-04 FLAT CHAIN, MINI HOPPER, IDLER GEAR AXLE 7 1 HSFC30-11 SPACER, DUAL HOPPER,MIXER WHEEL 8 1 65039 3/32" x 1-3/4" ZINC FINISH EXTENDED PRONG COTTER PIN 9 1 HSFC30-09 FLAT CHAIN, MINI HOPPER, IDLER GEAR STRIPPER 10 6 0148017 Type D - Wing Screw - Cup Point 1/4"-20x1 Zinc 11 2 HSFC11-35 GUIDE, FC DRIVE 12 8 21157 BOLT, CARRIAGE 1/4-20 X 1 1/4 Zn 13 12 60596 WASHER, LOCK 1/4'' ZINC 14 8 60570 NUT, HEX, 1/4-20 ZINC 15 8 60572 HEX, NUT 3/8-16 16 8 60853 WASHER, FLAT USS 3/8 X 1" ZINC 17 4 60598 WASHER, LOCK 3/8" ZINC 18 4 52088 BOLT, EYE, 3/8-16 X 2-1/2" LENGTH ZINC 19 2 HSFC19-33 FLAT CHAIN, 2 LINE HOPPER, OUTPUT FEED LEVEL SET 1 1 HSFC30-01 DUAL LINE, FLAT CHAIN, HOPPER WELDMENT 2 1 HSFC19-23 FLAT CHAIN, MINI HOPPER, BACK COVER
Hog Slat Inc. Newton Grove, NC USA June 2026 23 Feed Systems 120 LB EXTENSION HOPPER (HSFC20) PARTS LIST (HSFC20) ITEM QTY PART NUMBER DESCRIPTION 1 4 HSFC20-2 HOPPER, EXTENSION, SIDE PANEL 2 1 HSFC20-3 HOPPER, EXTENSION, BASE PLATE 3 2 HSFC20-1 HOPPER, EXTENSION, TOP HALF 4 36 60500 BOLT, HEX, 1/4-20 X 1/2, ZINC 5 36 60596 WASHER, LOCK 1/4" ZINC 6 28 60570 NUT, HEX 1/4"-20-ZINC 7 12 80518 SCREW, SELF DRILLING #10-16 x 5/8" ZINC
Hog Slat Inc. Newton Grove, NC USA June 2026 24 Feed Systems 90° CORNER (HSFC2E)
Hog Slat Inc. Newton Grove, NC USA June 2026 25 Feed Systems DUAL TRACK FEED SYSTEM PARTS LIST (DUAL TRACK) ITEM PART NUMBER DESCRIPTION 1 HSFCM-10* CORNER, FLAT CHAIN, MALE 2 HS618-XXX TROUGH 10’ MEDIUM WIDE HEN 3 HSFC11-90 DRIVE UNIT, SINGLE LINE 90 FPM – FLAT CHAIN W/O MOTOR 4 HS656 COUPLER, 8”MEDIUM WIDE TROUGH 5 HSFC30 DUAL LINE, FLAT CHAIN, HOPPER (FILL ONLY) NOTES: 1.) FEED SYSTEMS UNDER 300’ REQUIRE ONE DRIVE UNIT. 2.) FEED SYSTEMS OVER 300’ REQUIRE TWO DRIVE UNITS.
Hog Slat Inc. Newton Grove, NC USA June 2026 26 Feed Systems DUAL TRACK CHAIN CORNER (HSFCM10L / HSFCM10R) PARTS LIST ITEM QTY PART NUMBER DESCRIPTION 1 4 HSFC2E FLAT CHAIN, CORNER 2 1 HSFCM-01 Plate, 4 Corner Assy, Male Flat Chain Less Brackets 3 2 HSFCM-02 Bracket, Male Flat Chain Single HSFC2, HSFCM-01 4 2 HSFCM-03 Bracket, Male Flat Chain Double HSFC2, HSFCM-01 5 1 HSFCM-05 Bracket, Male Flat Chain Cover HSFC2, HSFCM-01 6 1 HSFCM-06 TROUGH, FLAT CHAIN, PULLET
Hog Slat Inc. Newton Grove, NC USA June 2026 27 Feed Systems FLAT CHAIN SYSTEM COMPONENTS IMAGE COMPONENT PART # DESCRIPTION Chain HSFC-1 Chain, Type C Corner HSFC2E Corner, 90° w/ Suspension Hanger Dual Track Corner Assembly HSFCM-10L Corner Assembly, Dual Track (Left Leaning) Dual Track Corner Assembly HSFCM-10R Corner Assembly, Dual Track (Right Leaning) Hen Trough HS618-10 Trough, Medium Wide Flared, 10 ft. HS618-12 Trough, Medium Wide Flared, 12 ft. Hen Trough Cover HS618-C20 Trough Cover, Medum Wide, 20” HS618-C60 Trough Cover, Medum Wide, 60” Coupler HS656 Coupler, 8” Medium Wide Flared
Hog Slat Inc. Newton Grove, NC USA June 2026 28 Feed Systems Pullet Trough HS1120-10 Trough, Pullet, 10 ft. HS1120-12 Trough, Pullet, 12 ft. Pullet Trough Cover HSFCP-11 Trough Cover, Pullet 10 ft. Coupler HS1121 Coupler, 12” Pullet Coupler HS1187 Coupler, 6” Pullet Hanger HSH031 Hanger, Trough Medium Wide Hanger HSFCM-04R Hanger, Trough Dual Track Flat Chain Grille End Cap HSFC9 End Cap, Medium Wide Hi Pro Grille Guard
Hog Slat Inc. Newton Grove, NC USA June 2026 29 Feed Systems Grille End Cap HSFC10 End Cap, Pullet Grille Guard Grille End Cap HSFC12 End Cap, Medium Wide Lo Pro Grille Guard Grille End Cap HSFC31 End Cap, Dual Track Hi Pro Grille Guard Hopper Extension HSFC20 Hopper Extension, 207# Clean Out HSFC14 Cover, Trough Clean Out Motors HS9092 Motor, 1HP 1PH 1425/1750 RPM 50/60HZ 230V HS9036 Motor, 2HP 1PH 1750 RPM 60HZ 230V N9360 Motor, 2HP 3PH 1425/1750 RPM 50/60HZ 208-230V/460V Frequency Drive HSFI-1002A Frequency Drive, 2HP 240V (Required for use w/ N9360)
Hog Slat Inc. Newton Grove, NC USA June 2026 30 Feed Systems Stand GP-120A Stand, Flat Chain and 3 Perch Pipe w/ Legs (Recommended to anchor legs to perch pipe with bolt at least every 50’) Hanger GP-111 Hanger, Flat Chain Suspended, 3 Perch Pipe Hanger GP-112 Hanger, Flat Chain Suspended, 1 Perch Pipe Perch Pipe 617202 Pipe Tube 1.315"OD X 10' 16Ga Galv w/CrimpPerching Roost 617205 Pipe Tube 1.315"OD X 12' 16Ga Galv w/CrimpPerching Roost 6172024 Pipe Tube 1.315"OD X 124' 16Ga Galv w/Crimp-Perching Roost Stand HSFC22 Stand, Flat Chain Coupler Stand HSFC4 Stand, Flat Chain 90 Degree Corner Chain Breaker HSFC8 Chain Breaker, Flat Chain, Cast
Hog Slat Inc. Newton Grove, NC USA June 2026 31 Feed Systems HSFCG-XX FLAT CHAIN GRILLE SPECIFICATIONS Part # TYPE TROUGH A (in) B (in) C (in) D (in) E (in) INVENTORY END CAP HSFCG-01 Hen, Hi-Profile HS618-XX 5.45 2.25 6.25 1.69 60 Stock HSFC9 HSFCG-02 Hen, Hi-Profile HS618-XX 5.45 2.25 6.25 1.63 60 Special Order HSFC9 HSFCG-03 Hen, Low-Profile HS618-XX 4.85 2.25 3.50 1.69 60 Stock HSFC12 HSFCG-04 Hen, Hi-Profile HS618-XX 5.45 3.50 6.25 1.69 72 Special Order HSFC9 HSFCG-05 Hen, Hi-Profile HS618-XX 5.45 2.00 6.25 1.69 72 Stock HSFC9 HSFCG-06 Hen, Hi-Profile HS618-XX 5.45 2.25 6.25 1.69 72 Special Order HSFC9 HSFCG-07 Pullet, Low-Profile HS1120-XX 3.32 2.75 4.25 1.75 60 Special Order HSFC10 HSFCG-09 Hen, Hi-Profile HS618-XX 5.45 2.25 6.25 1.75 72 Special Order HSFC9 HSFCG-10 Hen, Low-Profile HS618-XX 4.85 2.25 3.50 1.69 72 Special Order HSFC12 HSFCG-11 Hen, Hi-Profile HS618-XX 5.45 2.50 6.25 1.69 60 Special Order HSFC9 HSFCG-12 Hen, Low-Profile HS618-XX 4.85 2.00 3.50 1.69 72 Special Order HSFC12 HSFCG-13 Hen, Hi-Profile HS618-XX 5.45 3.16 6.25 1.63 60 Special Order HSFC9 HSFCG-16 Hen, Low-Profile HS618-XX 4.85 2.73 3.19 1.69 60 Special Order HSFC12 HSFCG-17 Hen, Low-Profile HS618-XX 4.85 None 3.63 2.63 60 Special Order HSFC12 HSFCG-18 Male, Double-V HS618-XX 12.16 4.00 6.48 2.50 60 Stock HSFC31 HSFCG-19 Hen, Double-V HS618-XX 12.16 2.25 6.48 1.69 60 Stock HSFC31 HSFCG-20 Male, Double-V HS618-XX 12.16 4.00 6.48 2.50 72 Special Order HSFC31
Hog Slat Inc. Newton Grove, NC USA June 2026 32 Feed Systems TROUBLESHOOTING GUIDE Problem Potential Cause Corrective Action Corner wheel not turning Foreign object in corner Remove object Chain too loose Remove link(s) from chain Shear pin breaking Foreign object in system Remove object System overloaded Make sure corners turn freely Chain catching trough/coupler Check system level, bent trough/couplers Worn drive sprocket, power shoe, mixer wheel in hopper Check all components for wear and replace as needed Chain surging Tighten chain by removing link(s) Water in system Clear wet feed Feed build up in corner Reduce feed in system Motor stops frequently System overload-Hi Amp Check for foreign or anything adding additional load to system. Motor not wired correctly Check motor wiring on motor label Motor does not start Breaker is tripped Check breaker Thermo breaker on motor is tripped Check motor thermo breaker
Hog Slat Inc. Newton Grove, NC USA June 2026 33 Feed Systems Hog Slat Limited Warranty Hog Slat warrants products to be free from defects in material or workmanship for a period of twenty-four (24) months from the date of original purchase. Hog Slat will credit, repair, or replace, at its option any product deemed defective within this time period. Labor costs associated with the replacement or repair of the product are not covered by the Seller/Manufacturer. Conditions and Limitations 1. The product must be installed by and operated in accordance with the instructions published by the Seller/Manufacturer or Warranty will be void. 2. Warranty is void if all components are not original equipment supplied by the Seller/Manufacturer. 3. This product must be purchased from and installed by an authorized retailer/distributor or certified representative thereof or the Warranty will be void. 4. Malfunctions or failure resulting from misuse, abuse, negligence, alteration, accident, or lack of proper maintenance shall not be considered defects under the Warranty. 5. This Warranty applies only to components/systems for the care of poultry and livestock. Other applications in industry or commerce are not covered by this Warranty. 6. This Warranty applies only to the Original Purchaser of the product. The Seller/Manufacturer shall not be liable for any Consequential or Special Damage which any purchaser may suffer or claim to suffer as a result of any defect in the product. “Consequential” or “Special Damages” as used herein include, but are not limited to, lost or damaged products or goods, costs of transportation, lost sales, lost orders, lost income, increased overhead, labor and incidental costs and operational inefficiencies. THIS WARRANTY CONSTITUTES THE SELLER/MANUFACTURER’S ENTIRE AND SOLE WARRANTY AND THIS MANUFACTURER EXPRESSLY DISCLAIMS ANY AND ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, EXPRESS AND IMPLIED WARRANTIES AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSES SOLD AND DESCRIPTION OR QUALITY OF THE PRODUCT FURNISHED HEREUNDER. Hog Slat Retailers/Distributors are not authorized to modify or extend the terms and conditions of this Warranty in any manner or to offer or grant any other warranties for GrowerSelect products in addition to those terms expressly stated above. An officer of Hog Slat must authorize any exceptions to this Warranty in writing. The Seller/Manufacturer reserves the right to change models and specifications at any time without notice or obligation to improve previous models.
Hog Slat Inc. Newton Grove, NC USA June 2026 34 Feed Systems THIS PAGE LEFT BLANK INTENTIONALY
Hog Slat Inc. Newton Grove, NC USA June 2026 35 Feed Systems THIS PAGE LEFT BLANK INTENTIONALY
Hog Slat Inc. Newton Grove, NC USA June 2026 36 Feed Systems This equipment must be installed in accordance with all State and Local Codes and applicable Regulations which should be followed in all cases. Authorities having jurisdiction should be consulted before installations are made. Hog Slat, Inc. PO Box 300 Newton Grove, NC 28366 Phone: (910) 594-0219 Fax: (910) 594-1392 www.hogslat.com Copyright © 2020 by Hog Slat, Inc. Part Number: HSMANUAL-350 Revision A2 Market - Poultry Product Group - Grower Select
hogslat.comRkJQdWJsaXNoZXIy MTA3MzU=