PULLET PAN FEEDER OPERATIONS MANUA L 2025 1
HSMANUAL-255 February 2026 1|Page Classic Pullet Pan Feeding System Contents Safety Information ............................................................................................................................................. 2 Hog Slat Limited Warranty ................................................................................................................................. 3 Planning Guidelines ........................................................................................................................................... 4 Birds Per Pan Recommendations .................................................................................................................. 4 Choosing Feed Tube - Feeder Spacing .......................................................................................................... 4 System Speed and Length ............................................................................................................................. 4 Capacity and Choosing Settings .................................................................................................................... 5 Installation Guidelines ....................................................................................................................................... 6 Feed Tube Installation................................................................................................................................... 6 Feed Tube Indexing Guide ............................................................................................................................ 7 Auger Installation and Stretch ...................................................................................................................... 8 Feeder Assembly Instructions ........................................................................................................................... 9 Parts List Matrix ............................................................................................................................................... 13
HSMANUAL-255 February 2026 2|Page Classic Pullet Pan Feeding System Safety Information Caution, Warning and Danger Decals have been placed on the equipment to warn of potentially dangerous situations. Care should be taken to keep this information intact and easy to read at all times. Replace missing or damaged safety signs. Safety–Alert Symbol This is a safety–alert symbol. When you see this symbol on your equipment, be alert to the potential for personal injury. GrowerSelect equipment is designed to be installed and operated as safely as possible...however, hazards do exist. Signal Words Signal words are used in conjunction with the safety–alert symbol to identify the severity of the warning. DANGER ............identifies immediate hazards which WILL result in severe personal injury or death. DANGER WARNING............ identifies hazards or unsafe practices which COULD result in severe personal injury or death. WARNING CAUTION ...........identifies hazards or unsafe practices which COULD result in minor personal injury or product or property damage. CAUTION WARNING – ROTATING AUGER This decal is placed on the clean-out cover of the GROWFLEX Auger Control Unit. Severe personal injury will result if the electrical power is not disconnected, prior to servicing the unit. Use caution when working with the Auger – springing auger may cause personal injury. DANGER – ELECTROCUTION HAZARD Disconnect electrical power before inspecting or servicing equipment unless maintenance instructions specifically state otherwise. Ground all electrical equipment for safety. All electrical wiring must be done by a qualified electrician in accordance with local and national electrical codes. Ground all non-current carrying metal parts to guard against electrical shock. Apart from motor overload protection, electrical disconnects and over-current protection are not supplied with the equipment.
HSMANUAL-255 February 2026 3|Page Classic Pullet Pan Feeding System Hog Slat Limited Warranty Hog Slat warrants products to be free from defects in material or workmanship for a period of twenty-four (24) months from the date of original purchase. Hog Slat will credit, repair, or replace, at its option, any product deemed defective within this period. Labor costs associated with the replacement or repair of the product are not covered by the Seller/Manufacturer. Warranty Extension Coverage The Limited Warranty period is extended for GrowerSELECT® Classic Pullet Poultry Pan Feeders. Years from Date of Installation Amount Customer pays for Replacement 0 - 5 Years No Charge 5 - 6 Years 50% of Current List Price 6 - 7 Years 60% of Current List Price 7 - 8 Years 70% of Current List Price 8 - 9 Years 80% of Current List Price 9 - 10 Years 90% of Current List Price Conditions and Limitations 1. The product must be installed by and operated in accordance with the instructions published by the Seller/Manufacturer or Warranty will be void. 2. Warranty is void if all components are not original equipment supplied by the Seller/Manufacturer. 3. This product must be purchased from and installed by an authorized retailer/distributor or certified representative thereof or the Warranty will be void. 4. Malfunctions or failure resulting from misuse, abuse, negligence, alteration, accident, or lack of proper maintenance shall not be considered defects under the Warranty. 5. This Warranty applies only to components/systems for the care of poultry and livestock. Other applications in industry or commerce are not covered by this Warranty. 6. This Warranty applies only to the Original Purchaser of the product. The Seller/Manufacturer shall not be liable for any Consequential or Special Damage which any purchaser may suffer or claim to suffer as a result of any defect in the product. “Consequential” or “Special Damages” as used herein include, but are not limited to, lost or damaged products or goods, costs of transportation, lost sales, lost orders, lost income, increased overhead, labor and incidental costs and operational inefficiencies. THIS WARRANTY CONSTITUTES THE SELLER/MANUFACTURER’S ENTIRE AND SOLE WARRANTY AND THIS MANUFACTURER EXPRESSLY DISCLAIMS ANY AND ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, EXPRESS AND IMPLIED WARRANTIES AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSES SOLD AND DESCRIPTION OR QUALITY OF THE PRODUCT FURNISHED HEREUNDER. Hog Slat Retailers/Distributors are not authorized to modify or extend the terms and conditions of this Warranty in any manner or to offer or grant any other warranties for GrowerSELECT® products in addition to those terms expressly stated above. An officer of Hog Slat must authorize any exceptions to this Warranty in writing. The Seller/Manufacturer reserves the right to change models and specifications at any time without notice or obligation to improve previous models.
HSMANUAL-255 February 2026 4|Page Classic Pullet Pan Feeding System Planning Guidelines Birds Per Pan Recommendations An approximate number of birds per pan can be derived from this feed space required by the integrator. Based on a pan diameter of 13-inches, the calculation method is as follows: ( 13” X 3.1416 ) = Birds Per Pan Inches Of Feed Space Per Bird Choosing Feed Tube - Feeder Spacing The manufacturer recommendation for optimum feeder spacing is 17” between feeders, which can be obtained by using 4 feeders spacing on 10 ft. feed tubing. If adequate barn space is not available for this spacing, 4 feeders spacing on 9 ft. feed tubing is also acceptable for use. Part Number Description HSPFT175-410 Poultry Feed Tube - 10 ft, 4 feeder spacing (recommended) HSPFT175-810 Poultry Feed Tube - 10 ft, 4 feeder spacing w/ 4 Kwik Start holes (recommended) HSPFT175-409 Poultry Feed Tube - 9 ft, 4 feeder spacing (optional) HSPFT175-809 Poultry Feed Tube - 9 ft, 4 feeder spacing w/ 4 Kwik Start holes (optional) System Speed and Length When installing a feedline drive unit for use in pullets, the manufacturer recommends the use of a high-speed gearbox (range of 550 RPM – 700 RPM) for rapid feed distribution. When using a high-speed gearbox, it is essential to effectively manage auger tension for smooth and proper operation. Refer to Auger Installation and Stretch on page 8 for instruction and guidelines. Part Number Description HS9022D10-P Drive Unit, 3/4 HP w/ 693 RPM Gearhead HSGR010 Gearhead, 693/573 RPM at 60/50 Hz w/ 5/8 Output Shaft (recommended) The maximum recommended length of pullet feedline using a high-speed gearbox is 300 feet from drive unit to anchor bearing. It is recommended to split the feedline at center house when the feedline length needs to extend beyond 300 feet. NOTICE: The above recommendation by the manufacturer should in no way suggest a guarantee of performance or a product warranty beyond the warranty stated within the Hog Slat Limited Warranty section of this manual.
HSMANUAL-255 February 2026 5|Page Classic Pullet Pan Feeding System Planning Guidelines (continued) Capacity and Choosing Settings Though the number of pans placed in the barn is derived from a target of birds per pan, the capacity of those pans is equally important. Inches of available feed space is often common among manufacturers in the poultry market, though the capacity of those feeders will vary greatly. Knowing your feeder capacity during the planning phase provides a better expectation of what feed distribution will look like during the flock. Having too much capacity per feeder translates to reduced distribution that other efforts like indexing can’t fix. Feeder Capacity is dependent on the non-flood level setting and the presence or absence of a Restrictor Cone. The below table shows approximate feed capacities based on a nominal feed density of 40 lbs./ft³. More accurate weights can be calculated by taking the density of the feed intended for use, dividing it by 40 lbs./ft³, and then multiplying it by the table value for a specific feed level setting. Once the needed capacity per feeder is determined, it may fall in a range where with and without a restrictor cone overlap. In this case, it is recommended to use the restrictor cone at a higher setting rather than use no restrictor cone at a lower setting. This will shift more of the feeder capacity to within the pan itself and make for more immediate feed presentation. No Restrictor With Restrictor Feeder Model Setting 3 Setting 6 Setting 3 Setting 6 HS8010B 1.6 lbs. 1.9 lbs. 1.3 lbs. 1.6 lbs. HS8010D 1.6 lbs. 1.9 lbs. 1.3 lbs. 1.6 lbs. HS8020BF 1.8 lbs. 2.3 lbs. 1.5 lbs. 2.0 lbs. HS8020DF 1.8 lbs. 2.3 lbs. 1.5 lbs. 2.0 lbs. NOTICE: The above recommendation by the manufacturer should in no way suggest a guarantee of performance or a product warranty beyond the warranty stated within the Hog Slat Limited Warranty section of this manual.
HSMANUAL-255 February 2026 6|Page Classic Pullet Pan Feeding System Installation Guidelines Feed Tube Installation During installation of feed tube, rib alignment will change per the indexing guide chart as the line is assembled. Indexing hanger PN# HS1189 is used to hang indexed feed lines. The notches within the hanger directly correspond to the notches on the feeder. One hanger per feed tube should be used. After the feed tube is assembled and hung per the indexing chart, the feeders should be placed on the feed tube to match the hanger on each individual tube. If indexed and assembled appropriately, all feeders will hang straight down for uniform feed distribution within the pans.
HSMANUAL-255 February 2026 7|Page Classic Pullet Pan Feeding System Feed Tube Indexing Guide Anti-rotation index numbers are shown from perspective looking down the feed line from the hopper to the drive unit. Feeder cone should be oriented so that anti-rotation device is on the feed hopper side of the cone. Tube Quantity 20 21 22 23 24 25 26 27 28 29 30 Tube Number 1 5 5 5 5 5 5 5 5 5 5 5 2 5 5 5 5 5 5 5 5 5 5 5 3 5 5 5 5 5 5 5 5 5 5 5 4 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 6 5 5 5 5 5 5 5 5 5 5 5 7 5 5 5 5 5 5 5 5 5 5 5 8 5 5 5 5 5 5 5 5 5 5 5 9 5 5 5 5 5 5 5 5 5 5 5 10 5 5 5 5 5 5 5 5 5 5 5 11 6 6 5 5 5 5 5 5 5 5 5 12 6 6 6 6 5 5 5 5 5 5 5 13 6 6 6 6 6 6 5 5 5 5 5 14 6 6 6 6 6 6 6 6 5 5 5 15 6 6 6 6 6 6 6 6 6 6 5 16 7 6 6 6 6 6 6 6 6 6 6 17 7 7 6 6 6 6 6 6 6 6 6 18 7 7 7 6 6 6 6 6 6 6 6 19 7 7 7 7 6 6 6 6 6 6 6 20 7 7 7 7 7 6 6 6 6 6 6 21 7 7 7 7 7 6 6 6 6 6 22 7 7 7 7 7 6 6 6 6 23 7 7 7 7 7 6 6 6 24 7 7 7 7 7 6 6 25 7 7 7 7 7 6 26 7 7 7 7 7 27 7 7 7 7 28 7 7 7 29 7 7 30 7 If using mid-line control pans, index that particular feed tube and two tubes upstream in the #7 position so that the feed holes are in the full downward position. Index recommendations are for both 9’ and 10’ tubes.
HSMANUAL-255 February 2026 8|Page Classic Pullet Pan Feeding System Auger Installation and Stretch CAUTION CAUTION when installing flex auger as improper installation practices COULD result in minor personal injury or product or property damage. Auger under tension can spring if tension is released. Please disconnect electrical power to the connected drive unit before working with auger. Model 44 flex auger should be installed using safe installation methods per the following steps: 1. PUSH AUGER INSIDE FEED TUBE – This task should be completed with two personnel, one to uncoil the auger and one to slowly feed auger in the tube while inspecting auger to ensure no kinks are present. 2. ATTACH AUGER TO DRIVE UNIT – Once auger reaches the other end of the feed tube, attach auger to anchor bearing to secure one end of the auger. 3. PRE-STRETCH AUGER – From the end opposite of the drive unit where anchor bearing is to be installed, pull auger until tension is felt. With tension on the auger and all slack removed from the system, slowly release tension until the auger is resting in a relaxed state. Mark the auger where it exits the outlet tube of the weldment. 4. STRETCH AUGER – From the relaxed state, pull the auger under tension to remove 8” [200mm] per 100 ft [30m] of auger past the mark. Use vise grips to clamp the auger and hold under tension so this section of auger can be removed and that the anchor bearing can be installed. 5. INSTALL ANCHOR BEARING – With vise grips still clamped to the auger holding tension, install the anchor bearing. Pull anchor bearing to relieve and remove the vise grips. Slowing release tension until the anchor bearing seats in the weldment tube. Use a pipe clamp to secure the anchor bearing to the weldment. 6. AUGER RUN-IN PROCEDURE – Once system is fully assembled and properly stretched, the auger run-in procedure should be completed before adding feed to the system. Run the system dry with no feed for 5-10 minutes to remove any burns that may exist. After dry run-in is complete, feed may be added and auger used under normal operation.
HSMANUAL-255 February 2026 9|Page Classic Pullet Pan Feeding System Feeder Assembly Instructions Step #1: If using the HS8000-18 Restrictor, push it upward inside the HS8000-19* cone bottom. Be sure that locking tabs snap in the appropriate slot as shown. If you are not using a Restrictor Cone, please proceed with the next step. Step #2: Slide the HS8000-19* Cone Bottom up inside the HS8000-21 Adjuster until the flood window is completely closed. Step #3: Slide the assembled cones up into the chosen grille. Be sure to properly align the small arrow on the adjuster with the desired number for the non-flood feed level setting.
HSMANUAL-255 February 2026 10|Page Classic Pullet Pan Feeding System Step #4: If using the HS8000-24 collar for locking out the flood window function, install by simply placing it over the cone so that it rests on top edge of the adjuster. If not, proceed to next step. Step #5: Install the HS8000-17 Slide Shutoff by sliding it through the designated slot until the small retention pops through to the side edge of the cone as shown. 1.75” Ribbed Feed Tube 45mm Smooth Feed Tube Step #6 (On Ribbed Tube): Install the HS8000-22 Anti-Rotation Device on the feed tube by placing the tube rib in the appropriate slot per the indexing guide. The slots should be facing the direction of the feed hopper when installed. Step #6a (On Smooth Tube): If installing HS8000-22 Anti-Rotation Device on smooth 45mm tubing, snap device adjacent to the feed tube hole. Device can be secured to the pipe using a size SAE 36 hose clamp (PN# HSHC-36) over the shown hose clamp indent of HS8000-22.
HSMANUAL-255 February 2026 11|Page Classic Pullet Pan Feeding System Step #7: Install the feeder assembly on the pipe so that the Anti-Rotation Device nests inside the cone bottom slot as shown and the feed tube hole is centered over the cone bottom. Step #8: Slide the HS8000-21 Cone Top in place from the side until the center tab locks in place as shown. Cone Top should now be secure from sliding side-to-side. Step #9: Begin installing the pan by orienting the pan upside down and placing the hook on the grille as shown so it can then swing in the downward position.
HSMANUAL-255 February 2026 12|Page Classic Pullet Pan Feeding System Step #10: Fold pan under the grille and twist until the hook is touching the slide stop as shown. NOTE: You should hear an audible “CLICK” when pan is locked in place and secured. Not twisting until the audible “CLICK” is heard can result in pans falling open during use.
HSMANUAL-255 February 2026 13|Page Classic Pullet Pan Feeding System Parts List Matrix HS8010B HS8010D HS8020BF HS8020DF HS8000-16 Pan HS8000-17 Shutoff HS8000-18 Restrictor HS8000-19B Cone Bottom HS8000-19D Cone Bottom HS8000-20 Cone Top (1.75” tube) HS8000-21 Support Cone HS8000-22 Anti-Rotation HS8000-14 8-Spoke Grille HS8000-25 4-Spoke Grille
HSMANUAL-255 February 2026 14|Page Classic Pullet Pan Feeding System This Page Intentionally Left Black
HSMANUAL-255 February 2026 15|Page Classic Pullet Pan Feeding System This Page Intentionally Left Black
HSMANUAL-255 February 2026 16|Page Classic Pullet Pan Feeding System This equipment must be installed in accordance with all State and Local Codes and applicable Regulations which should be followed in all cases. Authorities having jurisdiction should be consulted before installations are made. Hog Slat, Inc. PO Box 300 Newton Grove, NC 28366 Phone: (910) 594-0219 Fax: (910) 594-1392 www.hogslat.com Copyright © 2026 by Hog Slat, Inc. Part Number: HSMANUAL-255 Rev A1 Market: Poultry Product Type – Grower Select
hogslat.comRkJQdWJsaXNoZXIy MTA3MzU=